07-15-2002
I would just put in generic addresses;
192.10.10.1 dhcp1
192.10.10.2 dhcp2
192.10.10.3 dhcp3
192.10.10.4 dhcp4
and then give it a go. I dont know what the licences are like on the router, they may be 3 hours or 4 days, either way I dont think that they will change too much (probably just enought to get on your neaves every now and again).
10 More Discussions You Might Find Interesting
1. IP Networking
I just installed solaris 8 on my comp....NIC was recognized at startup so it's allrite...
for hostname I so far put hostname
and for the IP I put in the 192.168.0.XX
can anyone instruct me step by step on what I should change and how about would I go seeting up the dsl connection ...
... (2 Replies)
Discussion started by: czoka
2 Replies
2. UNIX for Advanced & Expert Users
How do I configure my Solaris system to connect to internet thro Linksys DSL Router?
Thanks in adavnce. (9 Replies)
Discussion started by: praveenk
9 Replies
3. Shell Programming and Scripting
Hi,
I'm using Damn Small Linux 2.3, could you tell me which script starts up the browser when fluxbox loads?
Thanks
C19 (0 Replies)
Discussion started by: c19h28O2
0 Replies
4. UNIX for Advanced & Expert Users
Hi
can any one point me to a procdure to add lang to dsl os (Damn Small Linux )
TU :) (0 Replies)
Discussion started by: lione.heart
0 Replies
5. Shell Programming and Scripting
Hi
can any one point me to a procdure to add lang to dsl os (Damn Small Linux )
TU
:) (2 Replies)
Discussion started by: lione.heart
2 Replies
6. Linux
ive been playing around in dsl (damn small linux) live for some time and i love the simplicity of it. but when i go into cfdisk to partition my hard drive, it says like
"Fatal Error:Does not have permission"
i am trying out Xandros desktop os 2.0 right now on my laptop. Can some one help me... (4 Replies)
Discussion started by: Texasone
4 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to instal dsl to hd ,but cfdisk comand returns an error.
dmesg | grep hda returns :
Optarac DVD RW AD-7530B, ATAPI CD/DVD-rom drive
attached ide-scsi driver
So i figure that is the problem.Right?
What should i do? (1 Reply)
Discussion started by: SNAk55
1 Replies
8. Linux
I'm trying to instal dsl to hd ,but cfdisk comand returns an error.
dmesg | grep hda returns :
Optarac DVD RW AD-7530B, ATAPI CD/DVD-rom drive
attached ide-scsi driver
So i figure that is the problem.Right?
What should i do? (9 Replies)
Discussion started by: SNAk55
9 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I downloaded the DSL Linux, I am able to boot and work on it. But I want to install this on my old laptop. How do I do that? Please advise.
Thanks. (1 Reply)
Discussion started by: samnyc
1 Replies
10. SCO
I have a dual boot computer with Windows 7 Pro 64 on one drive and SCO OpenServer 5.0.7 on another drive. The DSL modem works perfectly on the Windows side; I can input the gateway and DNS address 192.168.1.1 in Windows network configuration.
On the UNIX side, I created the /etc/resolv.conf... (8 Replies)
Discussion started by: Transpower
8 Replies
LEARN ABOUT DEBIAN
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <stgt@vger.kernel.org>
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)