06-11-2002
Post the errors you get when using startx.
9 More Discussions You Might Find Interesting
1. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
2. Solaris
hi there,
i'm quite new to solaris and recently i've bought a ibm thinkpad...
now i intend to install a dual-boot system. in fact i've got it managed to install the end-user system
with dual-boot working. apart from following issue other devices got recognized...
this is what i've found out... (2 Replies)
Discussion started by: pseudocoder
2 Replies
3. Linux
Hello all,
I need to develop an application that would be used as a simulator to test various custom algorithms. As I have never embarked on this kind of work, I need some advice:
1. Which GUI library to use in Linux, GTK+ or FLTK? The simulator application needs to output various... (2 Replies)
Discussion started by: fox_hound_33
2 Replies
4. Slackware
Hi Guys,
I'm trying to install slackware 10.2 on a on compaq laptop with Sansung
HM121HI hard drive but I wonder what kernel should I use so it can recognize the had disk. Initially I've tried using sata.i and then try to use the fdisk utility to create the new partiotions but doesn't seem... (0 Replies)
Discussion started by: hariza
0 Replies
5. UNIX for Dummies Questions & Answers
Hi gurus,
I am trying to connect to wifi access point with terminal, I set up my own access point (no encryption or MAC filters)
I ran followings commands
$ sudo iwlist eth1 scanning
eth1 Scan completed :
Cell 01 - Address: 00:11:2F:A2:99:1C
... (1 Reply)
Discussion started by: wakatana
1 Replies
6. Hardware
Hello everybody,
I'm having troubles with Slackware 13.1 and network cards.
I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies
7. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
8. Ubuntu
Is it possible to install Ubuntu 11.04 or Ubuntu 11.10 in Lenovo Thinkpad E520-1143 Now it Powerd By windowd Xp Professional is it possible to install Ubuntu in it and supports all drivers for ma laptop such as VGA driver Sound,Wireless,Lan , fingerprint,camera pls reply r is it possible to... (0 Replies)
Discussion started by: babinlonston
0 Replies
9. Red Hat
Hi All,
I have a Thinkpad - T430, which is having the wireless card as "03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205".
This one i need to configure as wifi hotspot. which i believe need to configure hostapd.conf, this kind of configuration is new to me anybody done... (1 Reply)
Discussion started by: linux.amrit
1 Replies
chs(7D) Devices chs(7D)
NAME
chs - IBM ServeRAID PCI host adapter driver
DESCRIPTION
The chs driver is the IBM ServeRAID PCI controller driver.
PRECONFIGURATION
Known Problems and Limitations
To prevent data loss, a SCSI disk drive that is not defined as part of any physical pack within a logical drive will not be accessible
through the Solaris operating environment.
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The IBM ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before booting the Solaris operating environment You use the configuration utilities to set RAID levels, stripe parameters, cache
mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/chs.conf chs configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.10 27 November 2000 chs(7D)