Ethernet Post: 20293

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by...

2. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the...

3. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up?

4. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

5. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses...

6. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ...

7. Solaris

ethernet

my solris box network is unreachable how to solve this ipaddress assiagning and entry in vi /etc/host how to solve network is unreachable

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

LEARN ABOUT CENTOS

netlabel-config

netlabel-config(8)					      NetLabel Documentation						netlabel-config(8)

NAME

       netlabel-config - NetLabel configuration utility

SYNOPSIS

       netlabelctl reset| load

DESCRIPTION

       The  NetLabel  configuration utility, netlabel-config, is a script designed to make it easier for system administratiors to create, manage,
       and use complex NetLabel configurations.  The netlabel-config script uses the netlabelctl(8)  tool  and	/etc/netlabel.rules  configuration
       file to load a saved NetLabel configuration into the kernel and reset the kernel's NetLabel configuration to the default state when needed.

       reset  Removes any NetLabel configuration loaded into the kernel and resets the kernel's NetLabel state to the default.

       load   Loads the NetLabel configuration specified by /etc/netlabel.rules into the kernel.

EXIT STATUS

       Returns zero on success, errno values on failure.

NOTES

       The NetLabel subsystem is supported on Linux Kernels version 2.6.19 and later.  The static, or fallback, labels are only supported on Linux
       Kernels version 2.6.25 and later.  The domain mapping address selectors are only supported on Linux Kernels 2.6.28 and later.

       The NetLabel project site, with more information including the source code repository, can be found at http://netlabel.sf.net.	This  pro-
       gram is currently under development, please report any bugs at the project site or directly to the author.

AUTHOR

       Paul Moore <paul@paul-moore.com>

SEE ALSO

       netlabelctl(8)

paul@paul-moore.com						    31 May 2013 						netlabel-config(8)