TL(4)                                                      BSD Kernel Interfaces Manual                                                      TL(4)

NAME

     tl -- Texas Instruments ThunderLAN Ethernet device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

           device miibus
           device tl

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

           if_tl_load="YES"

DESCRIPTION

     The tl driver provides support for PCI Ethernet adapters based on the Texas Instruments ThunderLAN Ethernet controller chip.

     The ThunderLAN controller has a standard MII interface that supports up to 32 physical interface devices (PHYs).  It also has a built-in
     10baseT PHY hardwired at MII address 31, which may be used in some 10Mbps-only hardware configurations.  In 100Mbps configurations, a
     National Semiconductor DP83840A or other MII-compliant PHY may be attached to the ThunderLAN's MII bus.  If a DP83840A or equivalent is
     available, the ThunderLAN chip can operate at either 100Mbps or 10Mbps in either half-duplex or full-duplex modes.  The ThunderLAN's built-in
     PHY and the DP83840A also support autonegotiation.

     The tl driver supports the following media types:

     autoselect            Enable autoselection of the media type and options.  Note that this option is only available on those PHYs that support
                           autonegotiation.  Also, the PHY will not advertise those modes that have been explicitly disabled using the following
                           media options.

     10baseT/UTP           Set 10Mbps operation

     100baseTX             Set 100Mbps (Fast Ethernet) operation

     10base5/AUI           Enable AUI/BNC interface (useful only with the built-in PHY).

     The tl driver supports the following media options:

     full-duplex           Force full duplex operation

     half-duplex           Force half duplex operation.

     hw-loopback           Enable hardware loopback mode.

     Note that the 100baseTX media type is only available if supported by the PHY.  For more information on configuring this device, see
     ifconfig(8).

HARDWARE

     The tl driver supports Texas Instruments ThunderLAN based Ethernet and Fast Ethernet adapters including a large number of Compaq PCI Ethernet
     adapters.  Also supported are:

     o   Olicom OC-2135/2138 10/100 TX UTP adapter
     o   Olicom OC-2325/OC-2326 10/100 TX UTP adapter
     o   Racore 8148 10baseT/100baseTX/100baseFX adapter
     o   Racore 8165 10/100baseTX adapter

     The tl driver also supports the built-in Ethernet adapters of various Compaq Prosignia servers and Compaq Deskpro desktop machines including:

     o   Compaq Netelligent 10
     o   Compaq Netelligent 10 T PCI UTP/Coax
     o   Compaq Netelligent 10/100
     o   Compaq Netelligent 10/100 Dual-Port
     o   Compaq Netelligent 10/100 Proliant
     o   Compaq Netelligent 10/100 TX Embedded UTP
     o   Compaq Netelligent 10/100 TX UTP
     o   Compaq NetFlex 3P
     o   Compaq NetFlex 3P Integrated
     o   Compaq NetFlex 3P w/BNC

DIAGNOSTICS

     tl%d: couldn't map memory  A fatal initialization error has occurred.

     tl%d: couldn't map interrupt  A fatal initialization error has occurred.

     tl%d: device timeout  The device has stopped responding to the network, or there is a problem with the network connection (cable).

     tl%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

     tl%d: no memory for tx list  The driver failed to allocate an mbuf for the transmitter ring when allocating a pad buffer or collapsing an
     mbuf chain into a cluster.

SEE ALSO

     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The tl device driver first appeared in FreeBSD 2.2.

AUTHORS

     The tl driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

BSD                                                                July 16, 2005                                                               BSD