03-26-2002
AoE, look into hping2, it's a pretty straightforward tool, and it's all done from the command line as options.
10 More Discussions You Might Find Interesting
1. Programming
I am working on a project, which has the following type of hardware setup.
A special hardware device is receiving data from an external network interface. So we can have multiple such a hardware devices. Now these hardware devices will route the captured incoming data through the external... (4 Replies)
Discussion started by: S.P.Prasad
4 Replies
2. IP Networking
there are a number of clients connected to a server.... how can i count that each clients recieve ...? how do i moniter the activity of the client..? (2 Replies)
Discussion started by: damn_bkb
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
My Solaris Workstation has got 4 NICS, out of which one of them(bge3) is unplugged from the rest of the external network & connected to other interface(bge1). The isolated NIC serves as a simulated Ethernet Interface for my application under development.
Now, I'd like to capture RAW... (1 Reply)
Discussion started by: smanu
1 Replies
4. UNIX for Advanced & Expert Users
salutation experts,
I want to counting arrival and outgoing packets in a specific interval (ethernet interface), what library or method you offer me that i can use it in c lang?
tnx (1 Reply)
Discussion started by: galaxy.ice
1 Replies
5. Shell Programming and Scripting
Hello
I need to send some packets to check connection. Packets will be catch by snoop. Is there any Sun tool to send some packets on selected IP and Port?
Thx (1 Reply)
Discussion started by: miojamo
1 Replies
6. HP-UX
Hi there,
are there any functions that can get the packets statistics on UNIX ?
thanks. (2 Replies)
Discussion started by: Frank2004
2 Replies
7. Infrastructure Monitoring
Hello,
SNMP reports from my Linux server a large number of "ipInAddrErrors" on several of my systems. According to one description, these packets are discarded datagrams due to:
How do I determine what packets these are? Can tcpdump help? If so, can anyone suggest a filter? (1 Reply)
Discussion started by: otheus
1 Replies
8. Solaris
Is there anywhere we can get details about what we should expect to see and not to see in some packets captured with "snoop" during troubleshooting a problem? I know we can capture packes for a failed transaction and compare them with packets for a successful trasaction.Is that the only way to... (4 Replies)
Discussion started by: Pouchie1
4 Replies
9. IP Networking
hello,
i am searching a way to delay the incoming packets before it goes out of the system may i know how can i approach to this problem? (3 Replies)
Discussion started by: sameer kulkarni
3 Replies
10. Solaris
I was checking routing table, and noticed that our server has a lot packets from localhost:
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
..
127.0.0.1 127.0.0.1 ... (1 Reply)
Discussion started by: orange47
1 Replies
LEARN ABOUT DEBIAN
ibping
IBPING(8) OpenIB Diagnostics IBPING(8)
NAME
ibping - ping an InfiniBand address
SYNOPSIS
ibping [-d(ebug)] [-e(rr_show)] [-v(erbose)] [-G(uid)] [-C ca_name] [-P ca_port] [-s smlid] [-t(imeout) timeout_ms] [-V(ersion)] [-c
ping_count] [-f(lood)] [-o oui] [-S(erver)] [-h(elp)] <dest lid | guid>
DESCRIPTION
ibping uses vendor mads to validate connectivity between IB nodes. On exit, (IP) ping like output is show. ibping is run as client/server.
Default is to run as client. Note also that a default ping server is implemented within the kernel.
OPTIONS
-c stop after count packets
-f, --flood
flood destination: send packets back to back without delay
-o, --oui
use specified OUI number to multiplex vendor mads
-S, --Server
start in server mode (do not return)
COMMON OPTIONS
Most OpenIB diagnostics take the following common flags. The exact list of supported flags per utility can be found in the usage message
and can be shown using the util_name -h syntax.
# Debugging flags
-d raise the IB debugging level.
May be used several times (-ddd or -d -d -d).
-e show send and receive errors (timeouts and others)
-h show the usage message
-v increase the application verbosity level.
May be used several times (-vv or -v -v -v)
-V show the version info.
# Addressing flags
-G use GUID address argument. In most cases, it is the Port GUID.
Example:
"0x08f1040023"
-s <smlid> use 'smlid' as the target lid for SM/SA queries.
# Other common flags:
-C <ca_name> use the specified ca_name.
-P <ca_port> use the specified ca_port.
-t <timeout_ms> override the default timeout for the solicited mads.
Multiple CA/Multiple Port Support
When no IB device or port is specified, the port to use is selected by the following criteria:
1. the first port that is ACTIVE.
2. if not found, the first port that is UP (physical link up).
If a port and/or CA name is specified, the user request is attempted to be fulfilled, and will fail if it is not possible.
AUTHOR
Hal Rosenstock
<halr@voltaire.com>
OpenIB August 11, 2006 IBPING(8)