03-19-2002
appended these lines to /etc/system:
* hme driver modes
*
set hme:hme_adv_autoneg_cap=0
set hme:hme_adv_100T4_cap=0
set hme:hme_adv_100fdx_cap=1
set hme:hme_adv_100hdx_cap=0
set hme:hme_adv_10fdx_cap=0
set hme:hme_adv_10hdx_cap=0
switched the ethernet cable to hme0, and renamed hostname.hme1* (configured for 3 ip addresses)to hostname.hme0*.
After boot, use ndd and u will got this:
% ndd -get /dev/hme instance 2
% ndd -set /dev/hme instance 0
% ndd -get /dev/hme instance 0
% ndd -get /dev/hme link_status 0
% ndd -get /dev/hme link_speed 1
% ndd -get /dev/hme link_mode 1
So, the card is configured for 100 full duplex. Post back if that doesnt help..
9 More Discussions You Might Find Interesting
1. Cybersecurity
Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (2 Replies)
Discussion started by: s_aamir
2 Replies
2. Solaris
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Discussion started by: DarReNz
5 Replies
3. Red Hat
All,
I have a RedHat 9 box which I need to figure out how to get it to stay in full duplex mode after a reboot.
I have tried
ethtool -s eth0 speed 100 duplex full autoneg off
I have tried to add a line to the /etc/sysconfig/network-scripts/ifcfg-eth0 like this:
ETHTOOL_OPTS="speed... (4 Replies)
Discussion started by: bubba112557
4 Replies
4. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
5. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
6. UNIX for Dummies Questions & Answers
Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies
7. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
8. Solaris
I want a solaris zone,wich can get ip from dhcp external server
i configure my zone
net:
address not specified
allowed-address not specified
configure-allowed-address: true
physical: vnic1
defrouter not specified
vnic is linked to net0
dladm
net0 ... (6 Replies)
Discussion started by: Linusolaradm1
6 Replies
9. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
whois(1) User Commands whois(1)
NAME
whois - Internet user name directory service
SYNOPSIS
whois [-h host] identifier
DESCRIPTION
whois searches for an Internet directory entry for an identifier which is either a name (such as ``Smith'') or a handle (such as ``SRI-
NIC''). To force a name-only search, precede the name with a period; to force a handle-only search, precede the handle with an exclamation
point.
To search for a group or organization entry, precede the argument with * (an asterisk). The entire membership list of the group will be
displayed with the record.
You may of course use an exclamation point and asterisk, or a period and asterisk together.
EXAMPLES
Example 1: Using The whois Command
The command:
example% whois Smith
looks for the name or handle SMITH.
The command:
example% whois !SRI-NIC
looks for the handle SRI-NIC only.
The command:
example% whois .Smith, John
looks for the name JOHN SMITH only.
Adding ... to the name or handle argument will match anything from that point; that is, ZU ... will match ZUL, ZUM, and so on.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWrcmdc |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
SunOS 5.10 6 Nov 2000 whois(1)