How to force NIC full 100 dpx in Solaris 8 Post: 17642

9 More Discussions You Might Find Interesting

1. Cybersecurity

How to force NIC full 100 dpx in Solaris 8

Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown.

2. Solaris

change NIC to 1000 Mbps full duplex

Hi all, I tried to use this command ndd -set /dev/eri adv_1000fdx_cap 1 but i get a "operation failed, Invalid argument" anyone can help ? Thanks

3. Red Hat

RedHat 9 Force full duplex

All, I have a RedHat 9 box which I need to figure out how to get it to stay in full duplex mode after a reboot. I have tried ethtool -s eth0 speed 100 duplex full autoneg off I have tried to add a line to the /etc/sysconfig/network-scripts/ifcfg-eth0 like this: ETHTOOL_OPTS="speed...

4. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to...

5. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I...

6. UNIX for Dummies Questions & Answers

Will Linux force NIC into promiscuous mode?

Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into...

7. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

8. Solaris

Solaris zone with full working NIC

I want a solaris zone,wich can get ip from dhcp external server i configure my zone net: address not specified allowed-address not specified configure-allowed-address: true physical: vnic1 defrouter not specified vnic is linked to net0 dladm net0 ...

9. Solaris

Haed code nxge0 nic interface with full duplex & 1000mbps

Hi All I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only. Please also let me know how to do it online through command. regards

LEARN ABOUT LINUX

hme

HME(4)                                                     BSD Kernel Interfaces Manual                                                     HME(4)

NAME

     hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

           device miibus
           device hme

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

           if_hme_load="YES"

DESCRIPTION

     The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.

     All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
     transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.

HARDWARE

     The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.

     Cards supported by the hme driver include:

     o   Sun PCI SunSwift Adapter (``SUNW,hme'')
     o   Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
     o   Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
     o   Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
     o   Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
     o   Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')

NOTES

     On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
     using the setenv command or by eeprom(8).  If set to ``false'' (the default), the hme driver will use the system's default MAC address for
     all of its devices.  If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
     address.

     Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
     add-on cards except the single-port SBus versions.

SEE ALSO

     altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)

     Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996,
     http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf.

HISTORY

     The hme driver first appeared in NetBSD 1.5.  The first FreeBSD version to include it was FreeBSD 5.0.

AUTHORS

     The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.

BSD                                                                June 14, 2009                                                               BSD

9 More Discussions You Might Find Interesting

1. Cybersecurity