02-15-2002
network card physical reset error
Hi all
I am facing some problem with network card
i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency.
In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are configured and now due to some problem i am puting the backup hard disk and trying to boot One error is coming like
there is no interface hme0
SW Hme0 phy reset error this message is coming continuously.
for qfe0 interface also the same mesage is coming.
But when i am putting the oringinal harddisk both the interfaces are succesfully configured.
please suggest.as i wan't the back disk to be used for some time.
waiting for ur suggestion.
thanks
PRAFUL
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. Solaris
How do you test the physical network connection of an interface in solaris. I know that if you have an active connection and the cable gets yanked, you can look in the messages file to check for link failure messages. But is there any better way to see if you have good layer 2 connectivity? (1 Reply)
Discussion started by: tjlst15
1 Replies
4. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
Hi, all!
Can anybody tell me how can I reset network statistic, which could be
seen by command 'netstat -i' or 'dladm show-dev -s'?
Thank you for advance
Christian (2 Replies)
Discussion started by: Inventor
2 Replies
7. Solaris
After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks.
ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface
# ifconfig eg1000g0:2 plumb
ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface
# ifconfig... (2 Replies)
Discussion started by: andersonedouard
2 Replies
8. Solaris
I am using telnet instead of ssh because network/physical service is on maintenance mode. I can ping google and other internel machines. I can't ssh to this server because network/physical is dependency of ssh.
How can I fix this service. I can use network service but it is maintenance mode.... (8 Replies)
Discussion started by: getrue
8 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT OPENSOLARIS
sppptun
sppptun(1M) System Administration Commands sppptun(1M)
NAME
sppptun - PPP tunneling driver utility
SYNOPSIS
sppptun plumb
sppptun plumb protocol device
sppptun unplumb interface
sppptun query
DESCRIPTION
The sppptun utility is used to configure and query the Solaris PPP tunneling device driver, /dev/sppptun. Currently, only PPP over Ether-
net (PPPoE) is supported, so the plumb and unplumb arguments are used to specify Ethernet interfaces that are to be used for PPPoE, and the
query option lists the plumbed interfaces.
The use of sppptun to add interfaces is similar to the use of ifconfig(1M) to add interfaces to IP. The plumbing is done once for each
interface, preferably at system start-up time, and is not normally manipulated on a running system. If multiple instances of PPP are run
over a single interface, they share the plumbing to that interface. Plumbing for each session is not required (and not possible for PPPoE).
The proper way to plumb interfaces for PPPoE is to list the interfaces, one per line, in the /etc/ppp/pppoe.if file.
USAGE
sppptun plumb
When specified with no additional arguments, the plumb argument lists the protocols that are supported by the utility. These are the
strings that are used as the protocol argument below.
sppptun plumb protocol device
This plumbs a new interface into the driver. The protocol parameter is pppoe for the PPP-carrying "Session Stage" connection or pppoed
for the PPPoE "Discovery Stage" connection. Both connections must be present for each Ethernet interface that is to be used for PPPoE.
The device parameter is the path name of the Ethernet interface to use (use ifconfig(1M) to list available devices). If the path begins
with /dev/, then this portion may be omitted.
sppptun unplumb interface
This removes an existing interface from the driver and terminates any PPP sessions that were using the interface. The interface parame-
ter is the name of the interface as reported when the interface was plumbed.
sppptun query
Displays the canonical names of all interfaces plumbed into the /dev/sppptun device driver.
EXAMPLES
Example 1 Setting up to Use PPPoE on hme0
Plumb the hme0 interface.
# sppptun plumb pppoed hme0
hme0:pppoed
# sppptun plumb pppoe hme0
hme0:pppoe
Remove the hme0 interface.
# sppptun unplumb hme0:pppoed
# sppptun unplumb hme0:pppoe
Example 2 Script to Remove All Plumbed Interfaces
#!/bin/sh
for intf in `sppptun query`
do
sppptun unplumb $intf
done
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 One or more errors occurred.
FILES
/etc/ppp/pppoe.if list of Ethernet interfaces to be plumbed at boot time
/usr/sbin/sppptun executable command
/dev/sppptun Solaris PPP tunneling device driver
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpppdt |
+-----------------------------+-----------------------------+
SEE ALSO
pppd(1M), pppoec(1M), pppoed(1M), sppptun(7M)
RFC 2516, Method for Transmitting PPP Over Ethernet (PPPoE), Mamakos et al, February 1999
SunOS 5.11 19 Mar 2001 sppptun(1M)