Sponsored Content
Top Forums UNIX for Dummies Questions & Answers aggregate ethernet ports under Solaris Post 15087 by wizard on Saturday 9th of February 2002 10:27:12 PM
Old 02-09-2002
For Solaris 7 or earlier, look at Sun Trunking software. Make sure your switch is compatible with Sun Trunking software. If you are running Solaris 8 10/00 or later, you can use IP multi-pathing which is built into the kernel. Look at http://www.sun.com/docs and search for IP multi-pathing.
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. Solaris

[Please Help] ethernet problem on solaris

Hi All, i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below : Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded Sep... (2 Replies)
Discussion started by: bucci
2 Replies

4. Solaris

Configuring TP Ethernet in SPARCstation 5 Solaris 8

Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies

5. UNIX for Dummies Questions & Answers

NTP idle ports and ethernet interfaces

I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client. Thank you. *.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies

7. Solaris

IPMP over aggregate in Solaris 11

hi all, i start with solaris 11 and i am disapointed by the change on ip managing. i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande switch1 net0 aggregate1 | net1 aggregate1 |-----| |... (1 Reply)
Discussion started by: sylvain
1 Replies

8. AIX

Locating and Mapping Physical Ethernet Ports

Hello Everyone, Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ? Server with expansion box has around 12 ethernet ports (fibre and ethernet) what is the quickest way to map or find out en0 represents which physical port ? ... (1 Reply)
Discussion started by: filosophizer
1 Replies

9. Solaris

Solaris 11 ssh on machine with multiple Ethernet ports

I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs. I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are net0 192.168.1.82 net1 192.168.2.82 and so on till net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
purple-url-handler(1)						   User Commands					     purple-url-handler(1)

NAME
purple-url-handler - Python script to handle URL with purple SYNOPSIS
purple-url-handler [-URL] DESCRIPTION
Python script to handle URL with purple. OPTIONS
Usage: purple-url-handler URL Example: purple-url-handler "xmpp:romeo@montague.net?message" ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWgnome-im-client | +-----------------------------+-----------------------------+ |Interface stability |Volatile | +-----------------------------+-----------------------------+ SEE ALSO
purple-remote(1), purple-send(1), purple-send-async(1), attributes(5) purple-url-handler Manual, http://pidgin.im/ NOTES
Updated by Lei Ju, Sun Microsystems Inc., 2006, 2007. SunOS 5.11 02 Apr 2008 purple-url-handler(1)
All times are GMT -4. The time now is 03:17 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy