02-09-2002
A 3com 3c59x card /should/ have been detected during install by Redhat 7. Are you certain the card is functional? If you've modified your kernel in anyway, make sure you have the vortex/boomerang driver installed, as Neo said. Here's a detailed link to all things Linux and 3com NICs
http://www.scyld.com/network/vortex.html
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. Shell Programming and Scripting
I wonder how I shall read the result below, especially 'what'
shown below.
The result was shown when I entered 'w'.
E.g what is TOP? What is gosh ( what does selmgr mean?)?
login@ idle JCPU PCPU what
6:15am 7:04 39 39 TOP
6:34am 6:45 45 45 TOP
6:41am ... (1 Reply)
Discussion started by: Aelgen
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
Somehow someone created a file named '-ov' in the root directory.
Given the name, the how was probably the result of some cpio command they bozo'ed.
I've tried a number of different ways to get rid of it using * and ? wildcards, '\' escape patterns etc.. They all fail with " illegal option --... (3 Replies)
Discussion started by: GSalisbury
3 Replies
6. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT CENTOS
iptables-save
IPTABLES-SAVE(8) iptables 1.4.21 IPTABLES-SAVE(8)
NAME
iptables-save -- dump iptables rules to stdout
ip6tables-save -- dump iptables rules to stdout
SYNOPSIS
iptables-save [-M,--modprobe modprobe] [-c] [-t table]
ip6tables-save [-M,--modprobe modprobe] [-c] [-t table]
DESCRIPTION
iptables-save and ip6tables-save are used to dump the contents of IP or IPv6 Table in easily parseable format to STDOUT. Use I/O-redirect-
ion provided by your shell to write to a file.
-M,--modprobe modprobe_program
Specify the path to the modprobe program. By default, iptables-save will inspect /proc/sys/kernel/modprobe to determine the exe-
cutable's path.
-c, --counters
include the current values of all packet and byte counters in the output
-t, --table tablename
restrict output to only one table. If not specified, output includes all available tables.
BUGS
None known as of iptables-1.2.1 release
AUTHORS
Harald Welte <laforge@gnumonks.org>
Rusty Russell <rusty@rustcorp.com.au>
Andras Kis-Szabo <kisza@sch.bme.hu> contributed ip6tables-save.
SEE ALSO
iptables-restore(8), iptables(8)
The iptables-HOWTO, which details more iptables usage, the NAT-HOWTO, which details NAT, and the netfilter-hacking-HOWTO which details the
internals.
iptables 1.4.21 IPTABLES-SAVE(8)