02-04-2002
Which vendor/version of Linux? Under RedHat the information goes into a config file in /etc/sysconfig/network-scripts.
10 More Discussions You Might Find Interesting
1. Linux
Had problems in configuring USB memory stick in RHL 9.
Please assist.
With regards,
Kungra. (1 Reply)
Discussion started by: kungra2006
1 Replies
2. Shell Programming and Scripting
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
3. Solaris
hi friends,
I have brand new Sun Ultra 20 WS installed.
It was preinstalled with Solaris 10 6/06 system,
in ifconfig -a command only loop back intervace is showing.
and
/etc/path_to_install also not able to find the interface name.
my questions are:
1. Is there any command to get... (1 Reply)
Discussion started by: subhankar
1 Replies
4. Red Hat
Hi All
when I give the command,
$ ping <hostname>
I get the following error
ping: unknown host <hostname>
I have checked in the following files,
/etc/sysconfig/network
/etc/hosts
/etc/resolv.conf
/etc/nsswitch.conf
Every where in these files host name and IP address are given... (2 Replies)
Discussion started by: nagapradeep
2 Replies
5. AIX
I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8.
when I run the command
lsattr -El ent8
I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But... (10 Replies)
Discussion started by: thenomad
10 Replies
6. UNIX for Advanced & Expert Users
Can anybody please explain the below table to monitor NTP daemon status
This contains many columns like remote,refid,st....various values corresponding to those columns
If possible provide me any link to study about these quantities clearly.
It is very much required for my project please... (3 Replies)
Discussion started by: sgand
3 Replies
7. IP Networking
i have a linux server runnig oracle applications.
i need to access this server from putty using ssh through internet.
i did by registering my static ip with the dnydns.org and i am able to connect to the server.
but now there is no security to authenticate any user as any one knowing the... (6 Replies)
Discussion started by: u.n.i.x
6 Replies
8. Infrastructure Monitoring
I am trying to enabling SNMP access and trap forwarding for Linux(RHEL5) using following official url from IBM.
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/index.jsp?topic=/diricinfo/fqm0_t_enabling_snmp_access_and_trap_forwarding_for_linux.html
In my system, snmp and snmplibs are... (1 Reply)
Discussion started by: SiddhV
1 Replies
9. IP Networking
Can someone help with a detail step-by-step oh how to configure DNS server on Linux Server.
-
I need to have 3 IP addresses map to a single hostname.
for clients
I'm a Linux rookie.
Thanks
Oscar (1 Reply)
Discussion started by: FrankOscar
1 Replies
10. Red Hat
Dear Experts,
We have requirement to configure Dot matrix printer in linux, Also need to register in Oracle application R12.0.6 version where i need get the print in landscape format.
Request you all kindly help on the same.
Thank you,
Alone.
---------- Post updated 02-18-14 at 01:02... (6 Replies)
Discussion started by: Alone
6 Replies
LEARN ABOUT SUSE
ctrlaltdel
CTRLALTDEL(8) Linux Programmer's Manual CTRLALTDEL(8)
NAME
ctrlaltdel - set the function of the Ctrl-Alt-Del combination
SYNOPSIS
ctrlaltdel hard|soft
DESCRIPTION
Based on examination of the linux/kernel/sys.c code, it is clear that there are two supported functions that the Ctrl-Alt-Del sequence can
perform: a hard reset, which immediately reboots the computer without calling sync(2) and without any other preparation; and a soft reset,
which sends the SIGINT (interrupt) signal to the init process (this is always the process with PID 1). If this option is used, the init(8)
program must support this feature. Since there are now several init(8) programs in the Linux community, please consult the documentation
for the version that you are currently using.
ctrlaltdel is usually used in the /etc/rc.local file.
FILES
/etc/rc.local
SEE ALSO
simpleinit(8), init(8)
AUTHOR
Peter Orbaek (poe@daimi.aau.dk)
AVAILABILITY
The ctrlaltdel command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.
Linux 1.2 25 October 1993 CTRLALTDEL(8)