03-06-2001
Actually Neo, IE will run on Solaris 2.6 and I have installed it successfully. It will not install under Solaris 8.
bong m - If entering iexplore will start the browser (it's in your path), then what you entered should work to bring up the website in that browser. I have not tested it under IE, but I expect that it will work.
-Chuck
6 More Discussions You Might Find Interesting
1. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
2. Linux
I was wondering if it is possible to setup SFTP to go through the internet proxy while connecting to an internet location.
Problem: Client system is behind internet proxy. SFTP to any internet location fails as there is no documented way to configure SFTP to connect to internet locations through... (4 Replies)
Discussion started by: toobrown1
4 Replies
3. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
4. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
5. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
6. What is on Your Mind?
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
hman(1) General Commands Manual hman(1)
NAME
hman - browse the on-line manual pages
SYNOPSIS
hman [ -P browser ] [ -H host ] [ section ] name
hman [ -P browser ] [ -H host ] [ section ] [ index ]
DESCRIPTION
The hman script is an interface to man2html(1) that allows you to enter man page requests at the command line and view the output in your
favourite browser. The behaviour reminds of that of man(1) so that many people will be able to alias hman to man. If the browser used is
netscape, and an incarnation of netscape is running already, hman will pass the request to the existing browser.
OPTIONS
-P browser
Specify which browser (like lynx, xmosaic, arena, chimera, netscape, amaya, ...) to use. This option overrides the MANHTMLPAGER
environment variable. The default is the non-httpd version of lynx, or sensible-browser if lynx cannot be found.
-H host
Specify from what host to get the man pages. This option overrides the MANHTMLHOST environment variable. The default is localhost.
ENVIRONMENT
MANHTMLPAGER
The default browser to use is selected using this environment variable.
MANHTMLHOST
The default host to use is selected using this environment variable.
SEE ALSO
man(1), man2html(1), arena(1), lynx(1), sensible-browser(1), netscape(1), xmosaic(1), glimpse(1)
http://www.mcom.com/newsref/std/x-remote.html
19 January 1998 hman(1)