01-25-2002
k thx....
i think we will come tomorrow and perhaps sunday to restore this server...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I had Win98 and Win Xp on a dual boot on my system, I formatted my C: drive to get rid of Win98 and installed Linux Madrake in its Place, it all installed ok but when I boot up I can no longer dual boot and it goes straight into Mandrake Linux. How can I get either a dual boot so I can get to XP... (10 Replies)
Discussion started by: Merv
10 Replies
2. UNIX for Dummies Questions & Answers
i have instaled a boot loader and win98 on drive c: and linux on drive d: and when i go to boot with the loader into linux nottin happens.is there some way i should install lilo to let it boot of a loader on drive c: ? (5 Replies)
Discussion started by: perleo
5 Replies
3. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. AIX
Hi Guys
everyone know this problem on P595???
One of my servers, on boot, sleep 10-15 minute on led 0c33.
I know that it's a console problem... but i don't understand how resolve it.
Ideas???
P.S.
Sorry for my english.
Thanks.
Zio (0 Replies)
Discussion started by: Zio Bill
0 Replies
6. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
7. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
8. Solaris
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies
9. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
10. Red Hat
Hi,
My HP machine is using as boot device a disk defined in the Storage (IBM V5000). The connection is done by fiber connected through fiber switch.
No lacal disks are installed.
I'm using redhat 6.6.
I've installed and configured multipath.
Everything seems to work properly, however,... (0 Replies)
Discussion started by: Pazzeo
0 Replies
LEARN ABOUT REDHAT
ip6tables-restore
IPTABLES-RESTORE(8) iptables 1.6.1 IPTABLES-RESTORE(8)
NAME
iptables-restore -- Restore IP Tables
ip6tables-restore -- Restore IPv6 Tables
SYNOPSIS
iptables-restore [-chntv] [-M modprobe] [-T name] [file]
ip6tables-restore [-chntv] [-M modprobe] [-T name] [file]
DESCRIPTION
iptables-restore and ip6tables-restore are used to restore IP and IPv6 Tables from data specified on STDIN or in file. Use I/O redirection
provided by your shell to read from a file or specify file as an argument.
-c, --counters
restore the values of all packet and byte counters
-h, --help
Print a short option summary.
-n, --noflush
don't flush the previous contents of the table. If not specified, both commands flush (delete) all previous contents of the respec-
tive table.
-t, --test
Only parse and construct the ruleset, but do not commit it.
-v, --verbose
Print additional debug info during ruleset processing.
-M, --modprobe modprobe_program
Specify the path to the modprobe program. By default, iptables-restore will inspect /proc/sys/kernel/modprobe to determine the exe-
cutable's path.
-T, --table name
Restore only the named table even if the input stream contains other ones.
BUGS
None known as of iptables-1.2.1 release
AUTHORS
Harald Welte <laforge@gnumonks.org> wrote iptables-restore based on code from Rusty Russell.
Andras Kis-Szabo <kisza@sch.bme.hu> contributed ip6tables-restore.
SEE ALSO
iptables-apply(8),iptables-save(8), iptables(8)
The iptables-HOWTO, which details more iptables usage, the NAT-HOWTO, which details NAT, and the netfilter-hacking-HOWTO which details the
internals.
iptables 1.6.1 IPTABLES-RESTORE(8)