|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
How to configure tape drive on SUN
Post 11125 by s_aamir on Thursday 29th of November 2001 09:11:57 AM
11-29-2001
Yes you are right, it worked.
The reason is that, I want to run probe-scsi command on OK prompt as stated in manual. So when I ran this command it configures and shows the model of DAT.
Then I configure it SUN.
Thanks a lot.
The reason is that, I want to run probe-scsi command on OK prompt as stated in manual. So when I ran this command it configures and shows the model of DAT.
Then I configure it SUN.
Thanks a lot.
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I have a Sun Ultra 10/Solaris 2.7 with a differential SCSI card connected to a Supter DLt1 Tape Drive. When I boot the machine, and I do a probe-scsi-all in the very beginning of the boot process. It shows up correctly. If I wait for the boot process to proceed and then I do a probe-scsi-all, I get... (1 Reply)
Discussion started by: brv
1 Replies
2. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
3. UNIX for Dummies Questions & Answers
Hey guys,
I'm trying to mount a SUN DDS-2 tape drive on a SUN Ultra 80 machine running Solaris 9. I had the SCSI drive connected at time of install, I'm very new to Solaris so I don't know if Solaris would detect the drive like that and install some form of device driver. But, what im posting... (2 Replies)
Discussion started by: kingdbag
2 Replies
4. Solaris
hi,
need your help mentors I have external SCSI tape DRIVE COmpaq 15/30 GB DLT and I dont know how to install these and how to view if it is working. I'm also have another disk taken form my old sun and I want to use these also but my problem how I able to mount.
hope anyone can help me
... (9 Replies)
Discussion started by: eykyn17
9 Replies
5. AIX
Hi,
Help required!
How to mount internal tape drive of sun machine in AIX 5.3 (0 Replies)
Discussion started by: ashwin.krishna
0 Replies
6. Solaris
Can I do this live? Or, do I need to do a probe-scsi-all after doing a stop/A? (10 Replies)
Discussion started by: jgordon
10 Replies
7. Solaris
Hi everyone.
Im new to Sun Solaris or the Unix environment. My only background is the DOS command in windows and a little bit of c++ programming. I always worked with troubleshooting hardware and software issues with windows.
Now that I need to configure tape drives using sun solaris, I had... (11 Replies)
Discussion started by: graboid888
11 Replies
8. AIX
Hi,
I have recently purchase a SUN Storage Tek desktop LTO 4 HH tape drive and connected to a IBM AIX 5.1 server.
The server can detect the tape device.
Can someone please advice urgently.
Thanks (4 Replies)
Discussion started by: Caully
4 Replies
9. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
10. Solaris
I have a SunFire V445 running Solaris 10 and am adding a Sun DLT tape drive. From the OK prompt the probe-scsi-all does see the drive and it is the proper target of 4. When I do the boot -- -r it does build the /dev/rmt directories correctly and the links to /devices appear correct as well. When I... (8 Replies)
Discussion started by: chastings
8 Replies
LEARN ABOUT CENTOS
tapeinfo
TAPEINFO(1) General Commands Manual TAPEINFO(1) NAME
tapeinfo - report SCSI tape device info SYNOPSIS
tapeinfo -f <scsi-generic-device> DESCRIPTION
The tapeinfo command reads various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It issues raw commands directly to the tape drive, using either the operating system's SCSI generic device ( e.g. /dev/sg0 on Linux, /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems. One good time to use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API, 'tapeinfo' will report a more exact description of what went wrong. Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information. OPTIONS
The first argument, given following -f , is the SCSI generic device corresponding to your tape drive. Consult your operating system's doc- umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0). Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls them. Under Linux, "cat /proc/scsi/scsi" will tell you what SCSI devices you have. BUGS AND LIMITATIONS
This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT). AVAILABILITY
tapeinfo is currently being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of programs. The 'mtx' home page is http://mtx.sourceforge.net and the actual code is currently available there and via SVN from http://source- forge.net/projects/mtx. SEE ALSO
mt(1),mtx(1),scsitape(1),scsieject(1),loaderinfo(1) TAPEINFO1.0 TAPEINFO(1)