11-15-2001
configuring the system
Hi,
I am trying to restore a tape from one system to another.
I want to restore the whole system.
The thing is that the first system has 2 disks and
the second has 1 disk but the capacity is the same.See below:
first system:
2 disks ---> 9Gb and 7Gb
second system:
1 disk ---> 16Gb
I set the partioning the same though, so whatever I have on the first system I have at the second as well. The thing is that the devices obviously going to be the same.
I would to know which files in specific are the ones that UNIX reads when it comes up?
For example must the the following file be changed
to the correct device, and if yes which other files
shall I consider ??
<pre>
isgsi01(root)8: more .cpr_config
CnFg/.CPR/
/dev/dsk/c0t0d0s0/pci@1f,4000/scsi@3/disk@0,0:a
</pre>
Thanks for your help !
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
what are the files needed for the installation of a dns server on linux (redhat 7x)? what service does it run and where are the files & services located? (1 Reply)
Discussion started by: lealyz
1 Replies
2. UNIX for Advanced & Expert Users
Hi Folks,
I would like to learn the basics of unix administration like configuring telnet, ftp, smtp,etc..
Could u suggest me a good site for learning it??? or the methodology that has to be followed for learning it???
TIA,
Nisha
:) (2 Replies)
Discussion started by: Nisha
2 Replies
3. UNIX for Dummies Questions & Answers
Hi all
I'm trying to get nagios up and running on FreeBSD 4.10
I installed the ports and just have to configure it
documentation supplied by nagios on how to configure the net-mgmt is not working for me. I tried everything possible but just can't seem to configure it.
Anybody have an... (1 Reply)
Discussion started by: stunner
1 Replies
4. IP Networking
I have a Windows laptop and a Sparc desktop. I'm trying to toy around with routing.
If have always on broadband from BT. My router ipaddress is:
192.168.1.1
This router uses DHCP.
My Laptop Ip is as follows:
Ethernet adapter Local Area Connection:
Connection-specific DNS... (1 Reply)
Discussion started by: Kongowea
1 Replies
5. Web Development
Hi,
Previously I was using squid-2.5 accelerated but due to link breaking issue, I have upgraded it to 2.6 but i am unable to configure it with accelerated support. Kindly help me to make it accelerated proxy server.
My 2.6 squid.conf :
##################################################... (0 Replies)
Discussion started by: jagnikam
0 Replies
6. UNIX for Dummies Questions & Answers
Hello there,
I installed Ajaxterm on my Ubuntu 9.04 machine, and it's running ok if I use :http://localhost:8022/ in my broswer. This is the problem , it can only be accessed localy. If I want to access it through internet from another computer, it fails. I've read the tutorials on how to... (1 Reply)
Discussion started by: wosis
1 Replies
7. UNIX for Dummies Questions & Answers
Can someone show me the basics on configuring SSH on Unix so I can access my Unix account remotely from Windows 7. Basically, I want to fire some scripts remotely.
I've already posted a thread on the Windows forum thinking my configuration was wrong on the Windows side. But the more I read the... (9 Replies)
Discussion started by: rm-r
9 Replies
8. UNIX for Dummies Questions & Answers
Hi guys,
I had Cpanel VPS hosting and switched to non managed VPS hosting.
My nameservers are configured as follows
ns1.mobz.ca 69.175.76.110
ns2.mobz.ca 69.175.76.111
Before switching my domain worked perfectly. Like webprofessionalsconnect.com with those settings worked. With new... (4 Replies)
Discussion started by: vahankh
4 Replies
9. AIX
Hello All,
I am trying to clone an entire AIX virtual machine to a new virtual machine including all partitions and OS.Can anyone help me on the procedure to follow? I am not really sure on how it can be done.Thanks in advance.
Please use CODE tags for sample input, sample output, and for code... (4 Replies)
Discussion started by: gull05
4 Replies
SCSI(4) Kernel Interfaces Manual SCSI(4)
Name
SCSI - Small Computer System Interconnect
Description
The ULTRIX system interfaces to disk and tape devices through the Small Computer System Interconnect (SCSI). Initial ULTRIX SCSI support
is limited to the Digital-supplied mass storage devices. The following devices are fully supported on the ULTRIX system:
o Winchester disks: RZ22, RZ23, RZ23L, RZ24, RZ55, RZ56, RZ57, RX23, RX26, RX33
o Magnetic tapes: TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
o Optical disks: RRD40, RRD42
Under the ULTRIX operating system, a SCSI device is referred to by its logical name. Logical names take the following form:
nn#
The nn argument is the two-character name; the number sign (#) represents the unit number. The two character names for SCSI devices are:
rz - RZ22, RZ23, RZ23L, RZ24, RZ55, RZ56, RZ57, RX23, RX26, RX33, RRD40, RRD42 disks
tz - TZ30, TZK50, TLZ04, TSZ05, TKZ08, and TZK10 tapes
The unit number is a combination of the SCSI bus number, either 0, 1, ... and the device's target ID number. The unit number is eight
times the bus number plus the target ID. For example, an RZ23 disk at target ID 3 on bus 0 would be referred to as rz3; a TZK50 tape at
target ID 5 on the second SCSI bus would be referred to as 13.
The SCSI bus has eight possible target device IDs. By default, one is allocated to the system. This allows for a maximum of seven target
devices connected to a SCSI bus.
Restrictions
The ULTRIX SCSI device driver does not operate with optical disks, other than the Digital-supplied devices.
The SCSI driver attempts to support on a best effort basis, non-Digital-supplied winchester disks and magnetic tapes.
The following notes apply to the driver's handling of non-Digital-supplied disks:
o These disks are assigned a device type of RZxx, instead of RZ22, RZ23, RZ23L, RZ55, RZ56, RZ57, RX23, RX26, or RX33. The RZxx disks
follow the same logical device naming scheme as the Digital-supplied disks.
o During the autoconfigure phase of the system startup, the driver prints the contents of the SCSI vendor ID, product ID, and the
revision level fields of the inquiry data return by the SCSI device.
o RZxx disks are assigned a default partition table. The default table can be modified by editing the sz_rzxx_sizes[8] entry in the
file The utility can also be used to modify the partition table on a RZxx disk.
o The only logical unit number (LUN) supported for each target ID is 0.
See Also
rz(4), tz(4), chpt(8)
SCSI(4)