10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I have make an menu in which first option is to start and second is to stop the services
echo "Please enter the appropriate choice for doing the operations"
echo "
1) STOP Services
2) START Services
case $choice in
1)
... (1 Reply)
Discussion started by: punpun66
1 Replies
2. UNIX for Advanced & Expert Users
Hi
I do a very simple monitoring of our OpenLDAP (runs in cronjob and generate alerts if unsuccessfull)
$ ldapsearch -h hostname.domain -D "cn=monitor_user,ou=People,dc=organisation" -w "password" -b "dc=organisation" -x "(&(cn=monitor_user)(ou=People))" dn | grep -v version
dn:... (4 Replies)
Discussion started by: slashdotweenie
4 Replies
3. Shell Programming and Scripting
The pro help!
Write a shell script setup for linux security policies include:
1. login (username and password login).
2. add, delete your username and password.
3. firewall.
Note: Write a shell script file as follows:
If login successful then
Step 2.
If step 2 succeeds (ie add,... (1 Reply)
Discussion started by: ngovuongbinhtay
1 Replies
4. Shell Programming and Scripting
Hello, Newbie question on scripting - I'm looking to create a simple script that will work on RHEL5 that will adjust the network settings: ip address, default gateway, and subnet mask. If anything else needs to be done (service network stop / start) or should be done to make settings active - I... (4 Replies)
Discussion started by: rojizo
4 Replies
5. Solaris
Hi Gurus,
I had downloaded the below script from the net and used it to get the Link and duplex settings in my Sun servers.
In all except one(Sol-5.10 on X86) i am getting output format like below:
root: /var/ADMIN/bin/speed_duplex.sh
Interface Speed Duplex
--------- ... (2 Replies)
Discussion started by: Hari_Ganesh
2 Replies
6. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
7. Solaris
Evening,
I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: up speed: 100 Mbps ... (13 Replies)
Discussion started by: brialt1
13 Replies
8. IP Networking
Yesterday i had a situation that cause me headache for a while , I have a web server running win2k3 it has 2 NIC's
one of them assigned to public area network
and the other is not functioning
The place where the server is ,
is messy and cables on the floor so any one can stumble with ... (2 Replies)
Discussion started by: h@foorsa.biz
2 Replies
9. HP-UX
Hi Folks,
I want the command to change the duplex settings of a HP-UX server.
Thanks in advance.
Sagar. (2 Replies)
Discussion started by: sag71155
2 Replies
10. Solaris
Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the... (3 Replies)
Discussion started by: saabir
3 Replies
ET(4) BSD Kernel Interfaces Manual ET(4)
NAME
et -- Agere ET1310 10/100/Gigabit Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device et
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_et_load="YES"
DESCRIPTION
The et driver supports PCI Express Ethernet adapters based on the Agere ET1310 chip.
The et driver supports the following media types:
autoselect Enable autoselection of the media types and options. The user can manually override the autoselected mode by adding media
options to the /etc/rc.conf file.
10baseT/UTP Set 10Mbps operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.
1000baseT Set 1000Mbps (Gigabit Ethernet) operation. The mediaopt option can only be set to full-duplex mode.
The et driver supports the following media options:
full-duplex Force full-duplex operation.
half-duplex Force half-duplex operation.
Note that the 1000baseT media type is only available if it is supported by the adapter. For more information on configuring this device, see
ifconfig(8).
HARDWARE
The et driver supports Agere ET1310 10/100/Gigabit Ethernet adapters.
TUNABLES
hw.et.rx_intr_npkts This value controls how many packets should be received before a receive interrupt is generated. The default value is
32. It is recommended to set this value above 38 to prevent the host from being livelocked under a high degree of
stress.
hw.et.rx_intr_delay This value delays the generation of receive interrupts in units of ~4 microseconds. It is used together with
hw.et.rx_intr_npkts to achieve RX interrupt moderation. The default value is 20.
hw.et.tx_intr_nsegs This value controls how many segments (not packets) should be transmitted before a transmit interrupt is generated. The
default value is 126. It is recommended to set this value below 280 to prevent the TX ring from underflowing.
hw.et.timer This value controls how often a timer interrupt should be generated. It is used together with hw.et.tx_intr_nsegs to
achieve TX interrupt moderation. The default value is 1000000000 (nanoseconds).
SEE ALSO
altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), vlan(4), ifconfig(8)
HISTORY
The et device driver first appeared in DragonFly 1.11. The first FreeBSD release to include it was FreeBSD 8.0.
AUTHORS
The et driver was written by Sepherosa Ziehau <sepherosa@gmail.com> for DragonFly. It was ported to FreeBSD by Xin LI <delphij@FreeBSD.org>.
BSD
December 9, 2011 BSD