10 More Discussions You Might Find Interesting
1. Solaris
show /HOST command shows that
status = OpenBoot Running
when in this state, can the power be unplugged from the server ?
we are unable to bring the status to "powered off". Even if we issue "stop /SYS" it will momentarily be in the powered off status and then go back to power on... (1 Reply)
Discussion started by: paulk93
1 Replies
2. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
3. AIX
Hi,
is it possible to find out ip address of user who has shutdown or rebooted the server , I have used the command errpt -a , in that it is showing server rebooted but it is not showing ip address who has shutdown the serve, even I have used command last reboot.
Please suggest.
Regards,
... (3 Replies)
Discussion started by: manoj.solaris
3 Replies
4. UNIX for Advanced & Expert Users
Hi All,
I want to shutdown the server if no one is actualy using it. Its a linux server.
I thought of sending a msg on users terminal for those who all are logged in and expecting a input from them.
If they will reply system should not get shutdown else it should not.
Can any one... (2 Replies)
Discussion started by: Sadhana
2 Replies
5. Programming
Hi,
I want to code TCP/IP client/server in linux application capable to fastly detect ethernet cable disconnection in any condition.
So I have activate SO_KEEPALIVE options and set TCP_KEEPCNT, TCP_KEEPIDLE and TCP_KEEPINTVL to 1.
When I disconnect ethernet cable I have the following... (5 Replies)
Discussion started by: jeje_clb
5 Replies
6. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
7. IP Networking
Hi,
I'm trying to communicate two servers (HP DLProliant 380 G5) via a crossover cable, but I don't get them to ping each other.
I am working in RHEL 4.
These are the steps I've performed:
1) Plugged the crossover cables in eth2.
(note: The cable is brand new. Also I built one myself... (3 Replies)
Discussion started by: jrodriguez365
3 Replies
8. IP Networking
Hi, I am trying to implement a server-client socket communication. My server and clients are in different PCs. During communications if the ethernet cable is removed from the server side it shows broken pipe due to unable to write on the socket. I want to know how to check whether the ethernet... (0 Replies)
Discussion started by: JagadishB
0 Replies
9. AIX
Hi Guys,
Please help in this...when we start HACMP services ..server is getting shutdon.
Error mesg from cluster.log.
Apr 14 08:43:27 bascop17 snmpd: NOTICE: SMUX trap: (0 0) (127.0.0.1+46302+1)
Apr 14 08:43:33 bascop17 topsvcs: (Recorded using libct_ffdc.a cv 2):::Error ID:... (1 Reply)
Discussion started by: b_manu78
1 Replies
10. Solaris
HI all,
i still have a problem when using null modem to see the output from my server(sun ultra en 3000).
i followed the instruction from the internet, but it is not working.
1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port).
2.... (3 Replies)
Discussion started by: waterbear
3 Replies
OPTIUPS(8) NUT Manual OPTIUPS(8)
NAME
optiups - Driver for Opti-UPS (Viewsonic) UPS and Zinto D (ONLINE-USV) equipment
NOTE
This man page only documents the hardware-specific features of the optiups driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
optiups was originally written against a PowerES 280es in nut-0.45. It was revised for nut-2.0.1 and tested against a PowerES 420E. It is
expected to work with at least the PowerES, PowerPS, and PowerVS models.
This driver additionally supports a Zinto D from ONLINE USV-Systeme AG because of their very similar commands, but it is unknown if it also
works with other UPS from them.
This driver will not work with the PowerES stock serial cable. You will need to construct your own three conductor cable:
UPS 6 -> PC 3
UPS 9 -> PC 2
UPS 4 -> PC 5
The cable for Online-USV uses pin UPS 7 (not UPS 4) -> PC 5.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5) file:
status_only
Only poll for critical status information. Without this, optiups (and all NUT drivers) poll all sorts of information from the UPS
fairly often. It is probably not often enough to hurt anything, so this option probably is not very useful, unless you have a flaky
serial connection or a highly loaded machine.
nowarn_noimp
Does not print warnings when the UPS reports that a variable is not implemented or not pollable. Without the option you will get a
message sent to your system logs each time NUT polls the UPS. If you specify nowarn_noimp, this message will only be logged once.
fake_lowbatt
This forces the low battery flag true. Without it, if you want to test your UPS, you will have to unplug it and wait until the battery
drops to a low/critical voltage level before NUT will respond and power down your system. With the flag, NUT should power down the
system soon after you pull the plug. When you are done testing, you should remove this flag.
For basic shutdown configuration testing, the command upsmon -c fsd is preferred.
powerup
Zinto D from ONLINE-USV cannot be identified when switched to standby. Set this flag to allow the driver to power-up your Zinto UPS.
This will also power-up your equipment connected to the UPS!
BUGS
On the 420E, ups.serial and ups.temperature are unsupported features. This is not a bug in NUT or the NUT driver, just the way things are
with this UPS.
AUTHOR
Russell Kroll, Scott Heavner, Matthias Goebl
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 OPTIUPS(8)
10-16-2009
