scsi_target_reap(9) [suse man page]

SCSI_TARGET_REAP(9)						  SCSI mid layer					       SCSI_TARGET_REAP(9)

NAME

       scsi_target_reap - check to see if target is in use and destroy if not

SYNOPSIS

       void scsi_target_reap(struct scsi_target * starget);

ARGUMENTS

       starget
	   target to be checked

DESCRIPTION

       This is used after removing a LUN or doing a last put of the target it checks atomically that nothing is using the target and removes it if
       so.

AUTHORS

       James Bottomley <James.Bottomley@hansenpartnership.com>
	   Author.

       Rob Landley <rob@landley.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 2.6.					     July 2010						       SCSI_TARGET_REAP(9)

TARG(4) 						   BSD Kernel Interfaces Manual 						   TARG(4)

NAME

     targ -- SCSI target emulator driver

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device targ

DESCRIPTION

     The targ driver provides an interface for usermode programs to emulate SCSI target devices.  A sample program that emulates a disk drive
     (similar to da(4)) can be found in /usr/share/examples/scsi_target.

     The targ driver supplies the control device /dev/targ.  After opening the device, the file descriptor must be bound to a specific bus/tar-
     get/LUN and enabled to process CCBs using the TARGIOCENABLE ioctl.  The process then uses write(2) to send CCBs to the SIM and poll(2) or
     kqueue(2) to see if responses are ready.  Pointers to completed CCBs are returned via read(2).  Any data transfers requested by the user CCBs
     are done via zero-copy IO.

IOCTLS

     The following ioctl(2) calls are defined in the header file <cam/scsi/scsi_targetio.h>.

     TARGIOCENABLE   (struct ioc_enable_lun) Enable target mode on the LUN specified by the following structure:

			   struct ioc_enable_lun {
				   path_id_t	   path_id;
				   target_id_t	   target_id;
				   lun_id_t	   lun_id;
				   int		   grp6_len;
				   int		   grp7_len;
			   };

		     The selected path (bus), target, and LUN must not already be in use or EADDRINUSE is returned.  If grp6_len or grp7_len are
		     non-zero, reception of vendor-specific commands is enabled.

     TARGIOCDISABLE  Disable target mode and abort all pending CCBs.  The CCBs may optionally be read as they complete.  TARGIOCENABLE can then be
		     called to activate a different LUN.  Multiple disable calls have no effect.  The close(2) system call automatically disables
		     target mode if enabled.

     TARGIOCDEBUG    (int) Enables CAM_PERIPH debugging if the argument is non-zero, otherwise disables it.

FILES

     <cam/scsi/scsi_targetio.h>   describes the usermode interface.
     /sys/cam/scsi/scsi_target.c  is the driver source file.
     /dev/targ			  is the control device.

SEE ALSO

     /usr/share/examples/scsi_target, ahc(4), isp(4), scsi(4)

     FreeBSD Target Information, http://www.root.org/~nate/freebsd/.

AUTHORS

     The targ driver first appeared in FreeBSD 3.0 and was written by Justin T. Gibbs.	It was rewritten for FreeBSD 5.0 by Nate Lawson
     <nate@root.org>.

BUGS

     Currently, only the ahc(4) and isp(4) drivers fully support target mode.

     The ahc(4) driver does not support tagged queuing in target mode.

BSD
								 December 13, 2011							       BSD