PCF(4) BSD Kernel Interfaces Manual PCF(4)NAME
pcf -- Philips I2C bus controller
SYNOPSIS
device pcf
In /boot/device.hints:
hint.pcf.0.at="isa"
hint.pcf.0.port="0x320"
hint.pcf.0.irq="5"
For one or more iicbus busses:
device iicbus
DESCRIPTION
The pcf driver provides support to the Philips PCF8584 I2C controller for the iicbus(4) system.
The PCF8584 is an integrated circuit designed in CMOS technology which serves as an interface between most standard parallel-bus microcon-
trollers/microprocessors and the serial I2C-bus. The PCF8584 provides both master and slave functions. Communication with I2C-bus is car-
ried out on a byte-wise basis using interrupt or polled handshake. It controls all the I2C-bus specific sequences, protocol, arbitration and
timing. The PCF8584 allows parallel-bus systems to communicate bidirectionally with the I2C-bus.
SEE ALSO iicbus(4)HISTORY
The pcf manual page first appeared in FreeBSD 3.0.
AUTHORS
This manual page was written by Nicolas Souchu.
BSD August 6, 1998 BSD
Check Out this Related Man Page
LPBB(4) BSD Kernel Interfaces Manual LPBB(4)NAME
lpbb -- parallel port I2C bit-banging interface
SYNOPSIS
device iicbus
device iicbb
device lpbb
device iic
DESCRIPTION
The lpbb driver supports the Philips official I2C parallel bit-banging interface.
LS05 pin 14 (Vcc) o -------
| | |
+--+--+---------------------+--+--+------------+------+-o 1 |
| | | | | | ===.1uF | +5V |
-------- [R][R][R] 3x10K 3x10K [R][R][R] LS05 | | |
| | | | | | | | pin 7 o-+------+-o 2 |
| 12 o-+--+ | | 3| 4 | | | (Gnd) | GND |
| 17 o-+-----|--|----| >o-------------+--|--|--------------+ | |
| | | | |/ 8 /|9 | | 10 /|11 +----+-o 3 |
| 15 o-+-----+--|--------------o< |------+--|------o< |----+ | SCL |
| | | 1| 2 | | | | |
| 9 o-+--------|----| >o-------------------+--------------+----+-o 4 |
| | | |/ 6 /|5 | | SDA |
| 11 o-+--------+----------------------------------o< |----+ -------
| 10 o-+-+ | 4-pin
| 13 o-+-+--oGND Connector
| 25 o-+-+ ------------------ Part List --------------------------
-------- | 1 - .1 uF capacitor | 6 - 10K 5% resistors |
25-pin male D | 1 - 4-pin connector | 1 - 25-pin male D connector |
connector to PC | 1 - 74LS05 open collector hex inverter |
printer port -------------------------------------------------------
SEE ALSO iicbb(4), iicbus(4), ppbus(4)HISTORY
The lpbb manual page first appeared in FreeBSD 3.0.
AUTHORS
This manual page was written by Nicolas Souchu.
BSD October 25, 1998 BSD
Can i use the sun solaris 10 to create Fat32 partition ? and i have another question im so confused between format command an fdisk within it, and mkfs and newfs, well what i got is that i have to use format to create partition physcially in my hard disk then i have to use mkfs or newfs (which is a... (2 Replies)
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
I was given my pcf file to login to work from home and wanted to use OpenVPN instead of the Cisco VPN client software. Can I use this pcf file with OpenVPN? I attempted to use vpnc:
http://wiki.centos.org/HowTos/vpnc
but it just times out
?? (2 Replies)
Hello,
When I run #mpcfg command,it dose not work (I dont have it).
I need this command for "fast boot" my cluster.
is there is a package to install it? OR i can`t because of the type of machines that I am using?! :rolleyes: (4 Replies)