PCIB(4) BSD Kernel Interfaces Manual PCIB(4)NAME
pcib -- PCI bridge driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device pci
DESCRIPTION
The pcib driver provides for host and PCI bridges in a PCI system.
BUGS
This man page is too short.
BSD January 18, 2008 BSD
Check Out this Related Man Page
PCCBB(4) BSD Kernel Interfaces Manual PCCBB(4)NAME
pccbb -- cardbus bridge driver
SYNOPSIS
device cbb
device pccard
device cardbus
device exca
DESCRIPTION
The pccbb driver implements the Yenta specification for CardBus bridges.
The following PCI cardbus and pcmcia bridges are supported:
Cirrus Logic PD6832
Cirrus Logic PD6833
Cirrus Logic PD6834
O2micro OZ6812
O2micro OZ6832
O2micro OZ6833
O2micro OZ6836
O2micro OZ6860
O2micro OZ6872
O2micro OZ6912
O2micro OZ6922
O2micro OZ6933
O2micro OZ6972
O2Micro OZ711E1
O2Micro OZ711M1
Ricoh RL4C475
Ricoh RL4C476
Ricoh RL4C477
Ricoh RL4C478
TI PCI-1031
TI PCI-1130
TI PCI-1131
TI PCI-1210
TI PCI-1211
TI PCI-1220
TI PCI-1221
TI PCI-1225
TI PCI-1250
TI PCI-1251
TI PCI-1251B
TI PCI-1260
TI PCI-1260B
TI PCI-1410
TI PCI-1420
TI PCI-1450
TI PCI-1451
TI PCI-1510
TI PCI-1515
TI PCI-1520
TI PCI-1530
TI PCI-1620
TI PCI-4410
TI PCI-4450
TI PCI-4451
TI PCI-4510
TI PCI-4520
TI PCI-[67]x[12]1
TI PCI-[67]x20
ENE CB710
ENE CB720
ENE CB1211
ENE CB1255
ENE CB1410
ENE CB1420
Toshiba ToPIC95
Toshiba ToPIC95B
Toshiba ToPIC97
Toshiba ToPIC100
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.cbb.debug Non-zero values cause more verbose information to be printed to aid in debugging problems with the bridge chipset.
SEE ALSO cardbus(4), exca(4), pccard(4)BSD July 21, 2004 BSD
Hi, there. Recently one of my friends used FreeBSD 4.8 to setup a web server, and the network connection is 100MB/s. But every time when the visitors approached 300 people, the network turned so slow, and eventually "dead". Why is that? And how should we solve this problem. I don't know what... (7 Replies)
My FreeBSD install at ad0s1, and Windows 2000 at ad2s1.
Everytime I start my FreeBSD, it shows me this message:
fdc0: cmd 3 failed at out byte 1 of 3
pmtimer 0 on isa0
fdc0: cannot reserve I/O port range (6 ports)
My Floppy drive info:
0x03F2 - 0x03F3
0x03F4 - 0x03F5
0x03F7 - 0x03F7... (6 Replies)
Hi!
Ive been following a OpenBSD thread from Dec 2003 "Issues multitasking during disk IO", and no "good" answer has still been given. I experience the same problems as he did. But ill explain my problem below for you who doesnt want to read a hole new thread.
First off, i been using OpenBSD... (2 Replies)
Hi everyone.I have an Audigy2 ZS sound card. I'm not a guru so don't send me faraway)) Well my card sounds only in front channels... can't setup 5.1.
and i can't made a microphone works.
PS: A have red this Yuriy Tsibizov (AKA chibis) many time.
Here is some system info
dmesg
Copyright... (0 Replies)
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
I can't find why but I suppose it is because of some hardware failures... I have a Sun Fire V490 with Solaris 10 5/08 which runs Sun Cluster 3.2 and it downs occasionally with a circumstances I can't define... Also I note some strange behavior after server failures: when I ran any diagnostics from... (6 Replies)
hi all,
i am configure zone according to this steps
and i face this error
could you please help to solv it
poolcfg -c 'create pset weblogic1-pset (uint pset.min=1; uint pset.max=1)'
poolcfg -c 'create pool weblogic1-pool'
poolcfg -c 'associate pool weblogic1-pool (pset weblogic1-pset)'
... (5 Replies)
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Dear all
Any help would be greatly appreciated, I have Solaris 10 installed on an M5000 SPARC machine. While rebooting it, we are faced with the following message then the OK prompt:
SPARC Enterprise M5000 Server, using Domain console
Copyright (c) 1998, 2010, Oracle and/or its affiliates. All... (25 Replies)
Hi,
I am using sun enterprise 420R server. Problem is on the monitor i am not able to see anything. I tried Serial connection, on terminal(using serial) i could see that POST(power on start tests) tests are being done, after that "timeout waiting for arp rarp packet" message keep displaying... (11 Replies)