AMDSBWD(4) BSD Kernel Interfaces Manual AMDSBWD(4)NAME
amdsbwd -- device driver for the AMD SB600/SB700/SB710/SB750 watchdog timer
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device amdsbwd
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
amdsbwd_load="YES"
DESCRIPTION
The amdsbwd driver provides watchdog(4) support for the watchdog timers present on AMD SB600 and SB7xx south bridge chips.
SEE ALSO watchdog(4), watchdog(8), watchdogd(8), watchdog(9)HISTORY
The amdsbwd driver first appeared in FreeBSD 9.0.
AUTHORS
The amdsbwd driver was written by Andiry Gapon <avg@FreeBSD.org>. This manual page was written by Andiry Gapon <avg@FreeBSD.org>.
BSD November 30, 2009 BSD
Check Out this Related Man Page
ICHWD(4) BSD Kernel Interfaces Manual ICHWD(4)NAME
ichwd -- device driver for the Intel ICH watchdog interrupt timer
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ichwd
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ichwd_load="YES"
DESCRIPTION
The ichwd driver provides watchdog(4) support for the watchdog interrupt timer present on all Intel ICH motherboard chipsets.
The ICH WDT counts down in ticks of approximately 0.6 seconds; the exact value depends on hardware quality and environmental factors. Sup-
ported watchdog intervals range from 2 to 63 ticks.
Note that on some ICH-based systems, the WDT may be present but disabled, either in hardware or by the BIOS. The ichwd driver attempts to
detect this condition and will refuse to attach if it believes the WDT is disabled.
SEE ALSO watchdog(4), watchdog(8), watchdogd(8), watchdog(9)
Using the Intel ICH Family Watchdog Timer (WDT), Intel Application Note AP-725, Document Number 292273-001.
HISTORY
The ichwd driver first appeared in FreeBSD 5.3.
AUTHORS
The ichwd driver was written by Wm. Daryl Hawkins <dhawkins@tamu.edu> of Texas A&M University and Dag-Erling Smorgrav <des@FreeBSD.org>.
This manual page was written by Dag-Erling Smorgrav <des@FreeBSD.org>.
BSD August 20, 2008 BSD
I have a huge matrix file containing some 1.5 million rows and 6000 columns. The matrix looks something like this:
1 2 3
4 5 6
7 8 9
3 4 5
I want to add all the numbers in the columns of this matrix and display the result to my stdout. This means that the numbers in the first column are:
... (2 Replies)
Hi,
Just trying to get to grips with sed and awk for some reporting for work and I need some assistance:
I have a file that lists policy names on the first line and then on the second line whether the policy is active or not.
Policy Name: Policy1
Active: yes
Policy... (8 Replies)
version info :
vi availabe with RHEL 5.4
I have a text file with 10,000 lines. I want to copy lines from 5000th line to 7000th and redirect to a file. Any idea how I can do this?
Note:
The above scenario is just an example. In my actual requirement, the file has 14 million lines and I want... (9 Replies)
Hi everyone,
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello,
I couldn't find an actual introduction thread, so I decided to just put this here.
I go by d0wngrade online. I have been programming in multiple languages for about 15+ years. I started with standard web design languages like HTML and CSS, but I then advanced from design to development... (2 Replies)
Hi guys...
The first active code line in AudioScope.sh is set -u .
This causes a complete exit if a variable is used/found but has not been allocated at the start of the program.
However, apart from writing code to do the task, is there a switch to to check which variables have been... (17 Replies)
Hi.
In thread https://www.unix.com/shell-programming-and-scripting/267833-grouping-counting.html rovf and I had a mini-discussion on grep and awk.
Here is a demo script that compares the awk and grep approaches for this single problem:
#!/usr/bin/env bash
# @(#) s2 Demonstrate group... (1 Reply)
Hello,
I have to fish out some specific columns from a file based on the header value. I have the list of columns I need in a different file. I thought I could read in the list of headers I need,
# file with header names of required columns in required order
headers_file=$2
# read contents... (11 Replies)
For those interested in installing dash shell on OSX Lion to help test POSIX compliancy of shell scripts, it is quite easy. I did it like this:
If you don't have gcc on your system:
0. Download and install the Command Line Tools for Xcode package from Sign In - Apple *
1. Download the dash... (2 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
I have data of an excel files as given below,
file1
org1_1 1 1 2.5 100
org1_2 1 2 5.5 98
org1_3 1 3 7.2 88
file2
org2_1 1 1 2.5 100
org2_2 1 2 5.5 56
org2_3 1 3 7.2 70
I have multiple excel files as above shown.
I have to copy column 1, column 4 and paste into a new excel file as... (26 Replies)
Dear All,
Taking a break from Vue.js coding for the site, SEO and YT videos; and hopefully addressing some well deserved criticism from some here that I have been too focused on the visual aspects of the forums versus the substance and the community....
While the "current generation... (9 Replies)
Hi all...
Well guys and gals, I jumped in at the deep end and found things that PERL cannot do by default.
Many tricky terminal escape codes are not catered for so I had to create workarounds.
One thing I searched for was this:
Passing perl variable to shell command
AND, @Neo this was... (15 Replies)