Do linux have a device file for ETHERNET CARD.

10 More Discussions You Might Find Interesting

1. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ...

2. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

3. Solaris

Gigaswift ethernet card on reboot

I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card...

4. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

7. AIX

Add PCI ethernet card?

Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure...

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT SUSE

mkfs.bfs

MKFS.BFS(8)						Linux System Administrator's Manual					       MKFS.BFS(8)

NAME

       mkfs.bfs - make an SCO bfs filesystem

SYNOPSIS

       mkfs.bfs [-N nr-of-inodes] [-V volume-name] [-F fsname] device [size-in-blocks]

DESCRIPTION

       mkfs.bfs creates an SCO bfs file-system on a block device (usually a disk partition or a file accessed via the loop device).

       The  size-in-blocks  parameter  is  the	desired size of the file system, in blocks.  If nothing is specified, the entire partition will be
       used.

OPTIONS

       -N     Specify the desired number of inodes (at most 512).  If nothing is specified some default number	in  the  range	48-512	is  picked
	      depending on the size of the partition.

       -V volume-label
	      Specify the volume label. I have no idea if/where this is used.

       -F fsname
	      Specify the fsname. I have no idea if/where this is used.

       -v     Be verbose.

EXIT CODES

       The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.

SEE ALSO

       mkfs(8).

AVAILABILITY

       The mkfs.bfs command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.

Util-linux 2.9x 						   12 Sept 1999 						       MKFS.BFS(8)

Linux