8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
3. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
4. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. IP Networking
Hi
(sorry for my bad English)
I'm trying to configure an US Robotics (USR5423) wirless usb adapter on Fedora 9. the device is detected, and i'm trying to configure a wireless connection.
When I want to activate the device using
#service network restart
or
# /etc/init.d/network restart... (0 Replies)
Discussion started by: teis
0 Replies
7. Solaris
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies
8. UNIX for Dummies Questions & Answers
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies
ifup(8) ifup(8)
NAME
ifup - bring a network interface up
ifdown - take a network interface down
SYNOPSIS
ifup [-nv] [--no-act] [--verbose] [-i FILE|--interfaces=FILE] [--allow CLASS] -a|IFACE...
ifup -h|--help
ifup -V|--version
ifdown [-nv] [--no-act] [--verbose] [-i FILE|--interfaces=FILE] [--allow CLASS] -a|IFACE...
DESCRIPTION
The ifup and ifdown commands may be used to configure (or, respectively, deconfigure) network interfaces based on interface definitions in
the file /etc/network/interfaces.
OPTIONS
A summary of options is included below.
-a, --all
If given to ifup, affect all interfaces marked auto. Interfaces are brought up in the order in which they are defined in /etc/net-
work/interfaces. If given to ifdown, affect all defined interfaces. Interfaces are brought down in the order in which they are
currently listed in the state file. Only interfaces defined in /etc/network/interfaces will be brought down.
--force
Force configuration or deconfiguration of the interface.
-h, --help
Show summary of options.
--allow=CLASS
Only allow interfaces listed in an allow-CLASS line in /etc/network/interfaces to be acted upon.
-i FILE, --interfaces=FILE
Read interface definitions from FILE instead of from /etc/network/interfaces.
-e PATTERN, --exclude=PATTERN
Exclude interfaces from the list of interfaces to operate on by the PATTERN. Notice that the PATTERN can be a full interface name
or substrings that match interfaces. Users could easily have unexpected behaviour if they use a small string to do the match.
-n, --no-act
Don't configure any interfaces or run any "up" or "down" commands.
--no-mappings
Don't run any mappings. See interfaces(5) for more information about the mapping feature.
-V, --version
Show copyright and version information.
-v, --verbose
Show commands as they are executed.
EXAMPLES
ifup -a
Bring up all the interfaces defined with auto in /etc/network/interfaces
ifup eth0
Bring up interface eth0
ifup eth0=home
Bring up interface eth0 as logical interface home
ifdown -a
Bring down all interfaces that are currently up.
NOTES
ifup and ifdown are actually the same program called by different names.
The program does not configure network interfaces directly; it runs low level utilities such as ip to do its dirty work.
FILES
/etc/network/interfaces
definitions of network interfaces See interfaces(5) for more information.
/var/run/network/ifstate
current state of network interfaces
KNOWN BUGS
/LIMITATIONS
The program keeps records of whether network interfaces are up or down. Under exceptional circumstances these records can become inconsis-
tent with the real states of the interfaces. For example, an interface that was brought up using ifup and later deconfigured using ifcon-
fig will still be recorded as up. To fix this you can use the --force option to force ifup or ifdown to run configuration or deconfigura-
tion commands despite what it considers the current state of the interface to be.
The file /var/run/network/ifstate must be writable for ifup or ifdown to work properly. On Ubuntu the /var/run location is a temporary
filesystem which is always writable and thrown away on shutdown. You can also use the --force option to run configuration or deconfigura-
tion commands without updating the file.
Note that the program does not run automatically: ifup alone does not bring up interfaces that appear as a result of hardware being
installed and ifdown alone does not bring down interfaces that disappear as a result of hardware being removed. To automate the configura-
tion of network interfaces you need to install other packages such as hotplug(8) or ifplugd(8).
AUTHOR
The ifupdown suite was written by Anthony Towns <aj@azure.humbug.org.au>.
SEE ALSO
interfaces(5), ip(8), ifconfig(8).
IFUPDOWN
22 May 2004 ifup(8)