10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
2. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
3. Red Hat
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (0 Replies)
Discussion started by: sam4919
0 Replies
4. Red Hat
Hi all Expertise,
I have following issue to solve,
SSL / TLS Renegotiation DoS (low) 222.225.12.13
Ease of Exploitation Moderate
Port 443/tcp
Family Miscellaneous
Following is the problem description:------------------
Description The remote service encrypts traffic using TLS / SSL and... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
5. Shell Programming and Scripting
Hi All,
I have bash script, so what is sintax script in bash for Enable and Disable Tab Key. Thanks for your help.:(
Thanks,
Rico (1 Reply)
Discussion started by: carnegiex
1 Replies
6. UNIX for Dummies Questions & Answers
Hi;
Is there a way to determine for sure how many NIC ports installed on my Linux box?
I tried to run "lspci" but not sure about the results, it's not clear.
Below are the results when i run both "ifconfig" & "lspci" on my Linux box i hope someone can help me finding the actual numbers of... (1 Reply)
Discussion started by: Katkota
1 Replies
7. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
8. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
9. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies
10. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
NVRAM(4) BSD Kernel Interfaces Manual NVRAM(4)
NAME
nvram -- non-volatile RAM
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device nvram
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
nvram_load="YES"
DESCRIPTION
The nvram driver provides access to BIOS configuration NVRAM on i386 and amd64 systems.
PC motherboard uses a small non-volatile memory to store BIOS settings which is usually part of its clock chip and sometimes referred as
``CMOS SRAM''. This driver exposes bytes 14 through 128 of the NVRAM, or a total of 114 bytes, at offset zero of the device file /dev/nvram.
This driver is useful for cloning machines that shares the same hardware configuration and need same BIOS setting tweaks.
IMPLEMENTATION NOTES
The BIOS NVRAM's bytes 16 through 31 are checksummed at byte 32. This driver does not take care for these checksums.
EXAMPLES
Backup existing BIOS NVRAM to nvram.bin:
dd if=/dev/nvram of=nvram.bin
Restore BIOS NVRAM from nvram.bin:
dd if=nvram.bin of=/dev/nvram
SEE ALSO
dd(1)
HISTORY
The nvram device driver first appeared in FreeBSD 6.4.
AUTHORS
The nvram device driver was written by Peter Wemm. This manual page was written by Xin LI.
BSD
February 8, 2010 BSD