How to change from tty03 to tty00 serial port in AIX 5.x?

10 More Discussions You Might Find Interesting

1. AIX

Connect GPS to serial port AIX 5.x

HI, Does anyone installed a GPS from his Serial port to an IBM Server serial port with AIX 5.X I would like the rs232 configuration you used on the GPS, and the ttys configuration from your server. Thanks in advance !!!

2. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

3. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

4. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

5. Solaris

Serial port on the T5140

What is the serial port on the T5140 used for.

6. AIX

Serial port in AIX

Hi, How can i configure my modem in AIX thru serial port (sa0-->tty0) I have two port serial card configured as sa0 I created tty1 which port is tty0 and which port is tty1 how can i know??

7. Programming

Programming serial port

Hello! Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements: 1. Serial port is opened in non-canonical mode. 2. All the time I need to check is there something to read. 3. If I have to write something I need to write it...

8. Solaris

Serial port issue

Hi, I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port. When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the...

9. Solaris

serial port signal

hi i am using solaris 9 on sparc . i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer . thanks for your help ....

10. Programming

serial port reading

Hai there, Can any one provide me with a ansi c source code for opening com1 or com2 and read data. The port is connected to another serial communication device on rs232 port. The o/s is Sco Unix 5.0.6 Matter urgent Viswanath

LEARN ABOUT OSF1

scc

scc(7)							 Miscellaneous Information Manual						    scc(7)

NAME

       scc - Serial keyboard/mouse/communications interface

SYNOPSIS

       controller   scc0   at tc0   slot 3   vector sccintr

DESCRIPTION

       Two  base  board  Zilog scc dual UARTS provide DEC 3000 series personal systems with keyboard, mouse, and serial communications interfaces.
       The serial communications interfaces can operate at baud rates from B50 to B57600 (see tty(7)).

       The driver for the scc interface supports hardware flow control using the Request to Send (RTS) and Clear  to  Send  (CTS)  signals.   When
       hardware  flow  control is enabled, the flow of input data is controlled by the RTS signal and the flow of output data is controlled by the
       CTS signal.  If the CTS signal is off, the driver will suspend output to that line until the CTS lead is reasserted.  Likewise, the  driver
       will  turn off the RTS lead to tell the device connected to the line to stop sending data as a result of congestion on the host side.  When
       the condition clears, the driver will turn on the RTS lead to tell the device to resume sending data.

       In alternate console configurations (that is, no graphics head), communications port 2 (/dev/tty01) becomes the system console. The  serial
       system console port always operates at 9600 BPS, 8-bits, no parity.  No modem or hardware flow control is supported.

RESTRICTIONS

       Data  communications  equipment attached to the console serial port in alternate console configurations must be set to 9600 BPS, 8-bits, no
       parity. The scc driver enforces this restriction.

       Only communications port 1 (/dev/tty00) includes full modem control.

FILES

       console terminal local terminal local terminal

RELATED INFORMATION

       console(7), devio(7), modem(7), tty(7), MAKEDEV(8) delim off

																	    scc(7)

AIX