p520 Service Processor's IP

10 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. AIX

running LPAR on power5 p520 hardware

picked up an old p520..and also spend sometimes to manage software: a) AIX 7.1 b) VIOS Server 2.2 attempting to run a few LPARs without much more $$$$, as this is a home-made projects.. machine hdisk0, pre-installed with AIX 7.1 a few questions: a) In order to run LPARs, I will...

3. AIX

VIO server on p520

trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think a few questions, on this practice AIX machine on AIX 7.1 VIO can only be installed if ASMI or HMC is running ??? if so, perhaps ASMI is much simpler, since I will need to...

4. AIX

p520 -- amber light

it shows up after the upgrade to SF240_415, after 2 hrs. amber light shows up on the led of 9111-520, but alog shows: everything seems to work, not sure what's going on..

5. AIX

P520 AIX com port (tty0) settings

I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line The settings are correct in both sides, But I can't establish a connection. I suspect that there's something that I should do regarding the...

6. AIX

Connecting to the service processor?

Hi Folks, I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two...

7. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum...

8. AIX

installing aix 5.2 on p520

hello everybody. Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please?

9. AIX

connecting to service processor on 44P 170

I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this?

10. HP-UX

Service processor not responding

I am receiving messages from HP-UX Server "The operating system is unable to communicate with the service processor. The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ". I need help in the following:...

LEARN ABOUT LINUX

pppoe-sniff

PPPOE-SNIFF(8)						      System Manager's Manual						    PPPOE-SNIFF(8)

NAME

       pppoe-sniff - examine network for non-standard PPPoE frames

SYNOPSIS

       pppoe-sniff [options]

DESCRIPTION

       pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe(8) to work.

       Some  DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field.  It is
       often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.

       To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)

       If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the  Ethernet  hub.   Plug
       two  computers into normal ports on the hub.  On one computer, run whatever software the DSL provider gave you on whatever operating system
       the DSL provider supports.  On the other computer, run Linux and log in as root.

       On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff.  If the ethernet interface is eth0, for exam-
       ple, type these commands:

	    ifconfig eth0 promisc
	    pppoe-sniff -I eth0

       On  the	other  machine, start your DSL connection as usual.  After a short time, pppoe-sniff should print recommendations for the value of
       PPPOE_EXTRA.  Set this value in /etc/ppp/pppoe.conf.  If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-
       mail this to pppoe@roaringpenguin.com along with the name of your ISP and the manufacturer and model number of your DSL modem.  This infor-
       mation will be collated and provided on the PPPoE web page for users who do not have two computers.

       After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:

	    ifconfig eth0 -promisc

OPTIONS

       -I interface
	      The -I option specifies the Ethernet interface to use.  Under Linux, it is typically eth0 or eth1.  The interface should be "up" and
	      in promiscuous mode before you start pppoe-sniff.

       -V     The -V option causes pppoe-sniff to print its version number and exit.

BUGS

       pppoe-sniff only works on Linux.

AUTHORS

       pppoe-sniff was written by David F. Skoll <dfs@roaringpenguin.com>.

       The pppoe home page is http://www.roaringpenguin.com/pppoe/.

SEE ALSO

       pppd(8), pppoe(8), pppoe-sniff(8), pppoe-relay(8), /usr/share/doc/pppoe/README.Debian.gz

4th Berkeley Distribution					    3 July 2000 						    PPPOE-SNIFF(8)

AIX