06-11-2016
Printer.
Run 'mkdev parallel'
You will need to know the i/o port (378/278) and the irq (7/5), which you can get from the CMOS, or the jumper settings on the parallel card.
reboot.
Run scoadmin-->printers-->4 printer management.
Add a local printer, give it a queue name, select the model either dumb, or crnlmap and select the device /dev/lp or /dev/lp0 probably.
The crnlmap driver will add a carriage return to every line feed in the printer file. Alternatively, you can change the configuration of the printer to add convert LF to CRLF.
Terminal Server.
I have never installed this particular device.
Install the hardware.
The associated software will either install using 'custom' or have its own installation routine.
The 'custom' program expects the files to be named VOL.000.000, VOL.000.001 etc.
First, start 'custom', either by entering custom at the # prompt, or starting 'scoadmin' and selecting software.
Select install new software, and select either diskette or cdrom for the media. If this works you will only need to answer whatever questions the install program asks.
If you get a message to the effect that the media is incorrect then the software has its own installation.
Very likely, you will copy the media to a temporary location, where you will run the install program (typically ./setup, or ./install.sh)
Once that is installed, you will then need to configure the ports on the terminal server: baud rate, parity, bits, and whether a terminal or printer is attached.
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Trying to mount a drive which has been dropped after corruption.
What is the quickets and esiest command to run and which switches? cheers
olly (1 Reply)
Discussion started by: ollyparkhouse
1 Replies
2. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
3. UNIX for Dummies Questions & Answers
I'm trying to mount tape drive so I can tar from a cd.
this is what i type: mount /dev/rsd2940.4 /mnt
this is what i get: mount /dev/rsd2940.4 on /mnt : Block device required
I have no idea what that is supposed to mean. It's my understanding that rsd2940.4 is the block device. An... (1 Reply)
Discussion started by: nic_stersic
1 Replies
4. Shell Programming and Scripting
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (0 Replies)
Discussion started by: dnicky
0 Replies
5. AIX
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (5 Replies)
Discussion started by: dnicky
5 Replies
6. UNIX for Dummies Questions & Answers
Hi there: I'm new here
Can anyone help me:
I have DS15 Alpha server : Unix 5.1B
Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit.
What is the exact comman to mount the DLTape IV??
How do i make backuo @ copy file to the tape?
Thanx to all (0 Replies)
Discussion started by: ayzeayem
0 Replies
7. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
8. AIX
Dear all,
I have a AIX server with logical 3 partitions and the server is connecting a tape drive. the first partition can successfully making a system backup to the tape but how can i fail to mount the tape to second and thrid partition. would anyone can help me to deal with it? what command... (3 Replies)
Discussion started by: rickhlwong
3 Replies
LEARN ABOUT MOJAVE
pam_mount
pam_mount(8) BSD System Manager's Manual pam_mount(8)
NAME
pam_mount -- Home Folder Mounting PAM module
SYNOPSIS
[service-name] function-class control-flag pam_mount [options]
DESCRIPTION
The Home Folder Mounting PAM module supports the authentication and session management function classes. In terms of the function-class
parameter, these are ``auth'' and ``session'' respectively.
The Home Folder Mounting Authentication Module
The Home Folder Mounting authentication module reads the mount authenticator from the PAM authentication context and caches it in the PAM
environment. The Home Folder Mounting Session Management Module must be used in conjunction with this module to remove the authenticator
from the PAM environment.
The Home Folder Mounting Session Management Module
The Home Folder Mounting session management module copies the mount authenticator from the PAM environment, removes it from the PAM environ-
ment, and uses its copy to mount the user's home folder if the user's OpenDirectory record indicates that an AFP, SMB, NFS or FileVault home
folder is to be used.
When the session is closed, the Home Folder Mounting session management module unmounts the user's home folder if it was mounted by this mod-
ule when the session was opened.
SEE ALSO
pam.conf(5), pam(8), DirectoryService(8)
BSD
February 7, 2009 BSD