This is related to one of my previous post but now with a slight difference: I need the "Updated:" to be in one line as well as the "Information:" on one line as well. These are in multiple lines right now as seen below. These can have 2 or more lines that needs to be in one line.
System name:... (8 Replies)
I can't decide if I should use AWK or PERL after pouring over these forums for hours today I decided I'd post something and see if I couldn't get some advice.
I've got a text file full of hundreds of events in this format:
Record Number : 1
Records in Seq : ... (3 Replies)
i have the file <infile> with ^M charactrer. i just wnt to know through script whether the file have ^M character or not.
Please let me know the script steps to check the same.
Thanks in Advance
Ganesh. (3 Replies)
Hello,
I need a program that read a file line by line and prints out lines 1, 2 & 3 after an empty line... An example of entries in the file would be:
SRVXPAPI001 ERRO JUN24 07:28:34 1775
REASON= 0000, PROCID= #E506 #1065: TPCIPPR, INDEX= 003F
... (8 Replies)
I am trying to combine lines with these conditions:
1. First line starts with text of "libname VALUE db2 datasrc" where VALUE can be any text.
2. If condition1 is met then continue to combine lines through a line that ends with a semicolon.
3. Ignore case when matching patterns and remove any... (5 Replies)
Hi,
I have a requirement where I need to combine two lines in a file based on first character of each line in a file.
Please find the sample content of the file below:
Code:
_______________________
5, jaya, male, 4-5-90, single
smart
6, prakash, male, 5-4-84, married
fair
7, raghavi,... (1 Reply)
Hi,
I have a requirement where I need to combine two lines in a file based on first character of each line in a file.
Please find the sample content of the file below:
Code:
_______________________
5, jaya, male, 4-5-90, single
smart
6, prakash, male, 5-4-84, married
fair
7, raghavi,... (1 Reply)
I have been searching and trying to come up with an awk that will perform the following on a
converted text file (original is a pdf).
1. Since the first two lines are (begin with) text they are removed
2. if $1 is a number then all text is merged (combined) into one line until the next... (3 Replies)
In the awk piped to sed below I am trying to format file by removing the odd xxxx_digits and whitespace after, then move the even xxxx_digit to the line above it and add a space between them. There may be multiple lines in file but they are in the same format. The Filename_ID line is the last line... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)