Sponsored Content
Operating Systems Solaris Network Config on Zone in a Guest LDOM Post 302765153 by os2mac on Friday 1st of February 2013 03:10:59 PM
Old 02-01-2013
Final solution

This turned out to be a noob/display issue.

dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 0 unknown vnet0
net1 Ethernet up 0 unknown vnet1
net2 Ethernet up 0 unknown vnet2
zone1/net2 Ethernet up 0 unknown vnet2
net3 Ethernet up 0 unknown vnet3
zone1/net3 Ethernet up 0 unknown vnet3

where Device=vnet0 =/= your vnet you named vnet0 in the control LDOM and assigned to this LDOM. it DOES equal the device # assigned to your vnet and is LABELLED vnet for your convenience/confusion

NOTE: don't name your vnets "vnetX" it WILL confuse you.
 

9 More Discussions You Might Find Interesting

1. Solaris

ldom and zone

hi, what is the difference between ldom and zone. can we install any other os than sun in ldom. thanks, snj. (2 Replies)
Discussion started by: snjksh
2 Replies

2. Solaris

Help needed - trying to run commands in Guest LDoms from Control LDOM

Hi Folks, I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level. Can the same be done with Guest LDoms while remaining at the control LDOM level? ... (4 Replies)
Discussion started by: momin
4 Replies

3. Solaris

Configuring zone and LDOM boot order

Is anyone aware of a method of configuring the boot order of zones and or LDOMS? (2 Replies)
Discussion started by: os2mac
2 Replies

4. Solaris

Disk expansion on LDOM Guest

Hi, There is LDOM Guest where I need to expand /u02 file systems on it. It is residing on a Solaris 11 Hypervisor (Primary Domain). The storage is expanded on vdisk presented to Hypervisor. I need steps to expand the /u02 on LDOM Guest. (2 Replies)
Discussion started by: vidya_sagar2003
2 Replies

5. Solaris

T4 replaced motherboard - recovering LDOM config?

T4-2 issues meant replacing motherboard. I thought the ldom config was automatically saved? Got the oracle document here. At the moment, unable to get ldoms back - here is the output from a few commands:- ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME... (4 Replies)
Discussion started by: psychocandy
4 Replies

6. Solaris

Login slowness from LDOM to ZONE

Need assitance in troubleshooting steps . Below is the issue I have LDOM which has 4 zones on it . One zone logging into the server takes 13sec where as other zones are quick . Troubleshooting steps which I did - Checked /var/tmp . Not many files - We have LDAP but thought that wouldnt be... (7 Replies)
Discussion started by: ajayram_arya
7 Replies

7. Solaris

Solaris 11 zone has no external network access (except to Global Zone)

Hi, hoping someone can help, its been a while since I used Solaris. After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin) However, the NGZ cannot access any other netwqork devices, it can't even see the default router ... (2 Replies)
Discussion started by: GazinLincoln
2 Replies

8. Solaris

Ldom guest volumen problem t8 Solaris 11

hello to everyone. im new member here. i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain. I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
Discussion started by: Liam_
2 Replies

9. UNIX for Beginners Questions & Answers

Solaris 11 LDOM guest network not working

I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest. This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
BPQPARMS(8)						   Linux System Managers Manual 					       BPQPARMS(8)

NAME
bpqparms - Configure BPQ ethernet devices. SYNOPSIS
bpqparms device [-a ethaddr] [-d ethaddr] [-vV] DESCRIPTION
Bpqparms allows the setting of the BPQ Ethernet options for a particular device. Each BPQ Ethernet device appears as a device named bpq0...bpqN which overlays the original Ethernet device, usually eth0...ethN. This device is an AX.25 device driver and allows AX.25 frames to be transmitted over an Ethernet to another machine using the same protocol. The default for the device is to send and receive BPQ Ether- net packets to the broadcast address. This program replaces the previous "axparms -dev" option. OPTIONS
-a ethaddr Allows the setting of which ethernet address will be accepted by the BPQ Ethernet device. -d ethaddr If specified on its own, will set the destination ethernet address will be used for transmitting and for receiving of BPQ ethernet packets. An address of "broadcast" sets it to the ethernet broadcast address. -v Displays the version number. -V The original version messages. SEE ALSO
ax25(4), axports(5), ifconfig(8). AUTHOR
Joerg Reuter DL1BKE <jreuter@poboxes.com> Linux 4 September 1996 BPQPARMS(8)
All times are GMT -4. The time now is 08:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy