I don't understand. If you don't configure ip-shared explicity, then zone is ip-exclusive by default.
So, you must now:
-remove address and router config from the previous example,
-boot zone,
-login to zone on console
After configuring zone:
-zlogin as normal user
-su to root
-configure dhcp
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
T4-2 issues meant replacing motherboard.
I thought the ldom config was automatically saved? Got the oracle document here.
At the moment, unable to get ldoms back - here is the output from a few commands:-
ldm list
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME... (4 Replies)
Need assitance in troubleshooting steps . Below is the issue
I have LDOM which has 4 zones on it . One zone logging into the server takes 13sec where as other zones are quick .
Troubleshooting steps which I did
- Checked /var/tmp . Not many files
- We have LDAP but thought that wouldnt be... (7 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT OPENSOLARIS
native
native(5) Standards, Environments, and Macros native(5)NAME
native - native branded zone
DESCRIPTION
The native brand uses the branded zones framework described in brands(5) to run zones installed with the same software as is installed in
the global zone. The system software must always be in sync with the global zone when using a native brand.
SUB-COMMANDS
The following native brand-specific subcommand options are supported in zoneadm(1M).
attach [-u] [-b patchid]...
For native zones, zoneadm checks package and patch levels on the machine to which the zone is to be attached. If the packages/patches
that the zone depends on from the global zone are different (have different revision numbers) from the dependent packages/patches on
the source machine, zoneadm reports these conflicts and does not perform the attach. If the destination system has only newer dependent
packages/patches (higher revision numbers) than those on the source system, you can use the -u option to update the attached zone to
match the -revision packages and patches that exist on the new system. With -u, as in the default behavior, zoneadm does not perform an
attach if outdated packages/patches are found on the target system.
For native zones, one or more -b options can be used to specify a patch ID for a patch installed in the zone. These patches will be
backed out before the zone is attached or, if -u was also specified, updated.
install [-a archive] | [-d path] [-p] [-s] [-u] [-v] [-b patchid]...
The native brand installer supports installing the zone from either the software already installed on the system or from an image of an
installed system running the same release. This can be a full flash archive (see flash_archive(4)) or a cpio(1) or pax(1) "xustar" ar-
chive. The cpio archive be compressed with gzip or bzip2. The image can also be a level 0 ufsdump(1M), a path to the top-level of a
system's root tree, or a pre-existing zone path.
With no options the zone is installed using same software as is running the global zone.
To install the zone from a system image either the -a or -d is required. Either the -u or -p option is also required in this case.
-a archive
The path to a flash_archive(4), cpio(1), or pax(1) "xustar" archive, or a level0 ufsdump(1M), of an installed system. cpio archives
may be compressed using gzip or bzip2.
-b patchid
One or more -b options can be used to specify a patch ID for a patch installed in the system image. These patches will be backed
out during the installation process.
-d path
The path to the root directory of an installed system. If path is a hyphen (-), the zonepath is presumed to be already populated
with the system image.
-p
Preserve the system configuration after installing the zone.
-s
Install silently.
-u
Run sys-unconfig(1M) on the zone after installing it.
-v
Verbose output from the install process.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzoneu |
+-----------------------------+-----------------------------+
|Interface Stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO cpio(1), pax(1), zlogin(1), zonename(1), sys-unconfig(1M), ufsdump(1M), zoneadm(1M), zonecfg(1M), flash_archive(4), attributes(5),
brands(5), privileges(5), zones(5), lx_systrace(7D)SunOS 5.11 13 Feb 2009 native(5)