I would try the script (make sure you run a chmod +x) and run the script like this
Now... for Oracle, if it will be for ASM it will still require a partition. You should learn some of the commands for fdisk from here:
and then create the associated partitions, but not put any file systems on them. If by backup, you mean dumps of the tables, then you will need a filesystem
mkfs.<filesystemtype> should get you started. Many people use ext3, but any number of file system types should work, such as jfs, xfs, etc.
Based on the output, it appears you are running SUSE, is this correct? Yast would help you with a lot of this if you are.
---------- Post updated at 01:38 PM ---------- Previous update was at 01:36 PM ----------
Also, since you are using SAN based storage, and probably using some sort of multi-pathing (SANs, by the way they work, tend to show you multiple paths to the storage, and the operating system confuses them with actual drives), you should reference your drives like they are in /etc/fstab
Using either devmapper or /dev/disk/by-id rather than the sd? designation.
i am using Interactive Unix 4.1.1 and i have a disk from a another unix machine which is Unix Slackware 2.1 i'm having problem mounting the disk. it gives me an error message, ??? is there any solution to this ???
it say the disk has invalid file system (1 Reply)
I have connected up second hard drive to my Sparcstation5, touched /reconfigure. and now would like to know how to mount the hard drive. I am trying to access /etc/passwd file on second disk to change root passwd but after connecting drive; touching reconfigure. don't know how to go about accessing... (2 Replies)
Hi Engg. ! :mad:
I have a harddisk on which SCO UNIX Open Server was installed. There was some data (in .dbf format) on it. Present condition of HDD is that it is not booting. Now I want to mount this HDD through other HDD on which SCO UNIX Open Server is installed by attaching... (0 Replies)
hi,
is that possible?
i installed one disk of a old rs/6000 in a linux machine.
the problem seems to be the partition layout.
linux fdisk tells me that aix disklabels are not supported,
so the problem seems to be the partition layout, not the filesystem.
does anybody know a way to access... (1 Reply)
Hi once more :p
Yesterday I reinstalled Solaris OS and now I can not mount pcfs HDD
SunOS unknown 5.10 Generic_142901-03 i86pc i386 i86pc
and what has been added in /etc/vfstab is
/dev/dsk/c1t0d0p1:c - /podaci - pcfs - yes rw
But as I said , my disk is... (4 Replies)
Can someone please help me out here.
I have SunSolaris server that has a ridiculous about of space on it. several hundred gigabytes of space. There are lots of partitions on this server that has at least 100Gs on them.
I want to mount just one of these partitions on my Linux server so I can... (4 Replies)
I am using Solaris 10. I have a raw device attached to my system which is
/dev/md/rdsk/d91
I want to mount this as a disk with file system on a mount point /u05.
Actually this raw device was earlier part of Oracle ASM. Now I have removed this disk from ASM, and want to use it as normal... (3 Replies)
I wasn't sure where to put this thread but since i use ubuntu for data recovery, I figured this is the best place. So, a friend passed me a 250G Western Digital hard disk the other day and said that his client needs to get her pictures off it. the problem: windows says it wants to reformat the... (13 Replies)
Dear Experts,
My buissness requierment is to place some automated files in Windows server, Now Can you help me to map the Windows folder into Linux server.
Windows Details:-windows 2003
Linux Details:-
$ uname -a
Linux testdb.mawarid.local 2.6.9-55.ELsmp #1 SMP Fri Apr 20 16:36:54 EDT 2007... (3 Replies)
Hi Folks -
I need to mount a Windows Share to a Linux server. What is the best/easiest way to do this?
Is this 'how-to' guide accurate:
How to Share Files Between Windows and Linux
Or is there a better method you could share?
Thanks! (8 Replies)
Discussion started by: SIMMS7400
8 Replies
LEARN ABOUT XFREE86
hpsa
HPSA(4) Linux Programmer's Manual HPSA(4)NAME
hpsa - HP Smart Array SCSI driver
SYNOPSIS
modprobe hpsa [ hpsa_allow_any=1 ]
DESCRIPTION
hpsa is a SCSI driver for HP Smart Array RAID controllers.
Options
hpsa_allow_any=1: This option allows the driver to attempt to operate on any HP Smart Array hardware RAID controller, even if it is not
explicitly known to the driver. This allows newer hardware to work with older drivers. Typically this is used to allow installation of
operating systems from media that predates the RAID controller, though it may also be used to enable hpsa to drive older controllers that
would normally be handled by the cciss(4) driver. These older boards have not been tested and are not supported with hpsa, and cciss(4)
should still be used for these.
Supported hardware
The hpsa driver supports the following Smart Array boards:
Smart Array P700M
Smart Array P212
Smart Array P410
Smart Array P410i
Smart Array P411
Smart Array P812
Smart Array P712m
Smart Array P711m
StorageWorks P1210m
Since Linux 4.14, the following Smart Array boards are also supported:
Smart Array 5300
Smart Array 5312
Smart Array 532
Smart Array 5i
Smart Array 6400
Smart Array 6400 EM
Smart Array 641
Smart Array 642
Smart Array 6i
Smart Array E200
Smart Array E200i
Smart Array E200i
Smart Array E200i
Smart Array E200i
Smart Array E500
Smart Array P400
Smart Array P400i
Smart Array P600
Smart Array P700m
Smart Array P800
Configuration details
To configure HP Smart Array controllers, use the HP Array Configuration Utility (either hpacuxe(8) or hpacucli(8)) or the Offline ROM-based
Configuration Utility (ORCA) run from the Smart Array's option ROM at boot time.
FILES
Device nodes
Logical drives are accessed via the SCSI disk driver (sd(4)), tape drives via the SCSI tape driver (st(4)), and the RAID controller via the
SCSI generic driver (sg(4)), with device nodes named /dev/sd*, /dev/st*, and /dev/sg*, respectively.
HPSA-specific host attribute files in /sys
/sys/class/scsi_host/host*/rescan
This is a write-only attribute. Writing to this attribute will cause the driver to scan for new, changed, or removed devices (e.g.,
hot-plugged tape drives, or newly configured or deleted logical drives, etc.) and notify the SCSI midlayer of any changes detected.
Normally a rescan is triggered automatically by HP's Array Configuration Utility (either the GUI or the command-line variety); thus,
for logical drive changes, the user should not normally have to use this attribute. This attribute may be useful when hot plugging
devices like tape drives, or entire storage boxes containing preconfigured logical drives.
/sys/class/scsi_host/host*/firmware_revision
This attribute contains the firmware version of the Smart Array.
For example:
# cd /sys/class/scsi_host/host4
# cat firmware_revision
7.14
HPSA-specific disk attribute files in /sys
/sys/class/scsi_disk/c:b:t:l/device/unique_id
This attribute contains a 32 hex-digit unique ID for each logical drive.
For example:
# cd /sys/class/scsi_disk/4:0:0:0/device
# cat unique_id
600508B1001044395355323037570F77
/sys/class/scsi_disk/c:b:t:l/device/raid_level
This attribute contains the RAID level of each logical drive.
For example:
# cd /sys/class/scsi_disk/4:0:0:0/device
# cat raid_level
RAID 0
/sys/class/scsi_disk/c:b:t:l/device/lunid
This attribute contains the 16 hex-digit (8 byte) LUN ID by which a logical drive or physical device can be addressed. c:b:t:l are
the controller, bus, target, and lun of the device.
For example:
# cd /sys/class/scsi_disk/4:0:0:0/device
# cat lunid
0x0000004000000000
Supported ioctl() operations
For compatibility with applications written for the cciss(4) driver, many, but not all of the ioctls supported by the cciss(4) driver are
also supported by the hpsa driver. The data structures used by these ioctls are described in the Linux kernel source file
include/linux/cciss_ioctl.h.
CCISS_DEREGDISK, CCISS_REGNEWDISK, CCISS_REGNEWD
These three ioctls all do exactly the same thing, which is to cause the driver to rescan for new devices. This does exactly the
same thing as writing to the hpsa-specific host "rescan" attribute.
CCISS_GETPCIINFO
Returns PCI domain, bus, device and function and "board ID" (PCI subsystem ID).
CCISS_GETDRIVVER
Returns driver version in three bytes encoded as:
(major_version << 16) | (minor_version << 8) |
(subminor_version)
CCISS_PASSTHRU, CCISS_BIG_PASSTHRU
Allows "BMIC" and "CISS" commands to be passed through to the Smart Array. These are used extensively by the HP Array Configuration
Utility, SNMP storage agents, and so on. See cciss_vol_status at <http://cciss.sf.net> for some examples.
SEE ALSO cciss(4), sd(4), st(4), cciss_vol_status(8), hpacucli(8), hpacuxe(8),
<http://cciss.sf.net>, and Documentation/scsi/hpsa.txt and Documentation/ABI/testing/sysfs-bus-pci-devices-cciss in the Linux kernel source
tree
COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the
latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux 2017-09-15 HPSA(4)