Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the... (3 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Hi there
We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is.
As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5.
#ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex.
I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters
STARTMODE=onboot
BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies
LEARN ABOUT NETBSD
eap
EAP(4) BSD Kernel Interfaces Manual EAP(4)NAME
eap -- AudioPCI audio device driver
SYNOPSIS
eap* at pci? dev ? function ?
audio* at audiobus?
joy* at eap?
midi* at eap?
options EAP_USE_BOTH_DACS
DESCRIPTION
The eap driver provides support for the Ensoniq AudioPCI and Creative Labs SoundBlaster PCI series of audio cards. All models based on the
ES1370, ES1371, and ES1373 chips are supported.
By specifying:
options EAP_USE_BOTH_DACS
a second audio device is attached. You can use it simply by directing audio output to it. This way it is possible for two different pro-
grams to use the "same" audio device simultaneously.
SEE ALSO ac97(4), audio(4), joy(4), midi(4), pci(4)HISTORY
The eap device driver appeared in NetBSD 1.4.
CAVEATS
The joystick port hardware works by emulating a legacy isa(4) joystick port, bypassing the pci(4) bus method for address allocation. This is
unlikely to work on PCI busses other than the primary one. There is also a possibility for conflicts with real ISA devices because the PCI
bus is probed before ISA. Use with caution.
BSD July 22, 2006 BSD