hi ,
Let me put it in a different way with words.
Assume the lottery have numbers from 1-50.
Out of this 50 numbers, I am going to pick up only 35 numbers randomly.
so, my total numbers would be 35 numbers shuffled from nos.
I have list of winning numbers in file.
Now, the... (9 Replies)
So, i made a simple lottery number generator like this:
for i in `seq 10`; do seq 1 35 | shuf -n 7 | sort -g | tr '\n' ' ' ;echo; done
i've file with winning numbers:
Eg:1 10 15 20 25 30 35
2 6 10 14 18 22 26
My problem here is how to compare or check if my generated numbers are match... (10 Replies)
Ten movies have been nominated as best motion picture by the International Press Academy, presentation of the 2012 Satellite Awards will be held on 16th December at Los Angeles, CA.
Place your bits here on one of the below nominated movie of your choice:-
Argo
... (0 Replies)
Script for if characters from positions 7-15 are matching with characters from position 211-219 then replace all char from 211-219 with 9 space.
Total length of record is 420. Here is the specification of the data in file.
Position Field Data Type... (5 Replies)
people i have a problem i have a 32 bits sparc processor, and solaris 64 bits processor, i install a oracle data base 64 bits, but my oracle will not run because my processor is from 32 bits this is ok??, i know if i have x86 i cannot install a 64 bits operatin system in a 32 bits processor.
... (0 Replies)
SBNI(4) BSD/i386 Kernel Interfaces Manual SBNI(4)NAME
sbni -- Granch SBNI12 leased line modem driver
SYNOPSIS
device sbni
DESCRIPTION
The sbni driver provides support for leased line modems of following models:
o SBNI12-02, SBNI12D-02
o SBNI12-04, SBNI12D-04
o SBNI12-05, SBNI12D-05, ISA and PCI
o SBNI12-10, SBNI12D-10, ISA and PCI
and a kit for data link over a voice band:
o SBNI12-11, SBNI12D-11, ISA and PCI.
In addition to the standard port and IRQ specifications, the sbni driver also supports a number of flags which can set baud rate, receive
level, and low three bytes of Ethernet MAC-address (high three are always 00:ff:01), because Granch modems are presented to the system as
Ethernet-like network cards.
The high byte of the flags is a bit field, it is used to specify SBNI adapter receive level/baud rate:
Bits 0-3: receive level (0x00..0x0f)
Bits 4-5: baud rate number:
00 - 0 baud rate (2Mb in fast mode/500kb in slow)
01 - 1 baud rate (1Mb/250kb)
10 - 2 baud rate (500kb/125kb)
11 - 3 baud rate (250kb/62.5kb)
Bit 6: use fixed receive level
if bit 6 is set then receive level will be set according to bits 0-3 value, otherwise receive level will be autodetected
Bit 7: use fixed baud rate
if bit 7 is set then baud rate will be set according to bits 4-5 value, otherwise baud rate is set to 2Mb
FILES
The sources for the driver reside in:
/sys/dev/sbni/if_sbni.c
/sys/dev/sbni/if_sbnireg.h
/sys/dev/sbni/if_sbnivar.h
SEE ALSO arp(4), netintro(4), ifconfig(8)HISTORY
The sbni device driver first appeared in FreeBSD 4.6.
AUTHORS
The sbni device driver for FreeBSD 4.x was written by Denis I. Timofeev, partially based on David Greenman's ed(4) driver. Earlier versions
(available on ftp.granch.com) were written by Alexey V. Zverev.
SBNI12 hardware was designed by Alexey V. Chirkov.
BSD January 8, 2002 BSD