4 More Discussions You Might Find Interesting
1. IP Networking
Hello;
Please,I did the clone on virtualBox, but the machines have the same IP address: eth2 Link encap: Ethernet HWaddr 8:00:27: f0: 92:19 inet addr: 192.168.1.4 Bcast: 192.168.1.255 Mask: 255.255.255.0
how to change the address please?
Thank you so much (6 Replies)
Discussion started by: chercheur857
6 Replies
2. SCO
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack... (1 Reply)
Discussion started by: dalek
1 Replies
3. Virtualization and Cloud Computing
Hello, guys!
I use Ubuntu 9.04 as desktop operating system and I want to make some tests on NetBSD. I tried to install as a virtual sistem on VirtualBox but it doesn't want to install. You can see the error in the attached file.
Do you guys have any clue about what the problem could be? (3 Replies)
Discussion started by: Sergiu-IT
3 Replies
4. Solaris
I've just installed VirtualBox on my PC and installed OpenSolaris as a virtual machine within it. The PC connects to the internet via a router and uses DHCP to get its IP address. How do I configure the OpenSolaris virtual machine to use the same DHCP server so I can connect it to the net. At the... (4 Replies)
Discussion started by: JerryHone
4 Replies
LEARN ABOUT SUNOS
rmmount
rmmount(1M) System Administration Commands rmmount(1M)
NAME
rmmount - removable media mounter for CD-ROM, floppy, Jaz drive, and others
SYNOPSIS
/usr/sbin/rmmount [-D]
DESCRIPTION
The rmmount utility is a removable media mounter that is executed by Volume Management whenever a removable medium, such as a CD-ROM or a
floppy, is inserted. The Volume Management daemon, vold(1M), manages removable media. rmmount can also be called by using volrmmount(1).
Upon insertion of a medium and following invocation of the volcheck(1) command, rmmount determines what type of file system (if any) is on
that medium. If a file system is present, rmmount mounts the file system in one of the locations listed below.
For a diskette (floppy):
/floppy/floppy0
symbolic link to mounted floppy in local floppy drive
/floppy/floppy_name
mounted named floppy
/floppy/unnamed_floppy
mounted unnamed floppy
For a CD-ROM or a DVD-ROM:
/cdrom/cdrom0
symbolic link to mounted CD-ROM in local CD-ROM drive
/cdrom/CD-ROM_name
mounted named CD-ROM
/cdrom/CD-ROM_name/partition
mounted named CD-ROM with partitioned file system
/cdrom/unnamed_cdrom
mounted unnamed CD-ROM
For a Zip drive:
/rmdisk/zip0
symbolic link to mounted Zip medium in local Zip drive
/rmdisk/Zip_name
mounted named Zip medium
/rmdisk/Zip_name/partition
mounted named Zip medium with partitioned file system
/rmdisk/unnamed_zip
mounted unnamed Zip medium
For a Jaz drive:
/rmdisk/jaz0
symbolic link to mounted Jaz medium in local Jaz drive
/rmdisk/Jaz_name
mounted named Jaz medium
/rmdisk/Jaz_name/partition
mounted named Jaz medium with partitioned file system
/rmdisk/unnamed_Jaz
mounted unnamed Jaz medium
For a generic "rmdisk" drive:
/rmdisk/rmdisk0
symbolic link to mounted removable medium in local removable medium drive
/rmdisk/rmdisk_name
mounted named removable medium
/rmdisk/rmdisk_name/partition
mounted named removable medium with partitioned file system
/rmdisk/unnamed_rmdisk
mounted unnamed removable medium
If the media is read-only (for example, a CD-ROM or a floppy with write-protect tab set), the file system is mounted read-only.
If a file system is not identified, rmmount does not mount a file system. See the System Administration Guide: Basic Administration for
more information on the location of CD-ROM, floppy, and other media without file systems. Also see volfs(7FS).
If a file system type has been determined, it is then checked to see that it is "clean." If the file system is "dirty," fsck -p (see
fsck(1M)) is run in an attempt to clean it. If fsck fails, the file system is mounted read-only.
After the mount is complete, "actions" associated with the media type are executed. These actions allow for the notification to other pro-
grams that new media are available. These actions are shared objects and are described in the configuration file, /etc/rmmount.conf. See
rmmount.conf(4).
Actions are executed in the order in which they appear in the configuration file. The action function can return either 1 or 0. If it
returns 0, no further actions will be executed. This allows the function to control which applications are executed.
In order to execute an action, rmmount performs a dlopen(3C) on the shared object and calls the action function defined within it. The def-
inition of the interface to actions can be found in /usr/include/rmmount.h.
File systems mounted by rmmount are always mounted with the nosuid flag set, thereby disabling setuid programs and access to block or char-
acter devices in that file system. Upon ejection, rmmount unmounts mounted file systems and executes actions associated with the media
type. If a file system is "busy" (that is, it contains the current working directory of a live process), the ejection will fail.
OPTIONS
-D Turn on the debugging output from the rmmount dprintf calls.
FILES
/etc/rmmount.conf removable media mounter configuration file
/usr/lib/rmmount/*.so.1 shared objects used by rmmount.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWvolu |
+-----------------------------+-----------------------------+
SEE ALSO
volcancel(1), volcheck(1), volmissing(1), volrmmount(1), fsck(1M), vold(1M), dlopen(3C), rmmount.conf(4), vold.conf(4), attributes(5),
volfs(7FS)
System Administration Guide: Basic Administration
SunOS 5.10 1 Mar 2004 rmmount(1M)