10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Programming
Hi
I try to communicate with a GSM modem, from C, for sending SMS.
I use standart AT-commands.
Working well with terminal.
There is no problem writing ti the port.
But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35... (4 Replies)
Discussion started by: dmiller
4 Replies
3. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
4. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
5. Windows & DOS: Issues & Discussions
Hello all.
I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions:
How can i configure the serial port on dos?
How can i telnet form dos to the serial port?
How can i set up a telnet server on the... (12 Replies)
Discussion started by: mghis
12 Replies
6. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
7. Programming
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies
8. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
9. UNIX for Advanced & Expert Users
I am using system running on red hat linux 4.
I had connected health measuring machine to the serial port and configured it
stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb
this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the... (4 Replies)
Discussion started by: netsavant
4 Replies
10. UNIX for Advanced & Expert Users
Hi ,
I need to have an application where in I am able to create a virtual Serial port on a UNIX machine for a remote device which is accessible by a IP address and a port number (by terminal server). Both the machine and the remote device are on the same network. So after this application is... (1 Reply)
Discussion started by: naveenkj
1 Replies
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)
NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS
-4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO
nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)
AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)