Serial port redirector

10 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. Programming

Read from serial port

Hi I try to communicate with a GSM modem, from C, for sending SMS. I use standart AT-commands. Working well with terminal. There is no problem writing ti the port. But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35...

3. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

4. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

5. Windows & DOS: Issues & Discussions

Telnet to a serial port

Hello all. I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions: How can i configure the serial port on dos? How can i telnet form dos to the serial port? How can i set up a telnet server on the...

6. AIX

Serial port in AIX

Hi, How can i configure my modem in AIX thru serial port (sa0-->tty0) I have two port serial card configured as sa0 I created tty1 which port is tty0 and which port is tty1 how can i know??

7. Programming

Programming serial port

Hello! Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements: 1. Serial port is opened in non-canonical mode. 2. All the time I need to check is there something to read. 3. If I have to write something I need to write it...

8. Programming

Serial port programming

I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than...

9. UNIX for Advanced & Expert Users

Communicating with Serial Port

I am using system running on red hat linux 4. I had connected health measuring machine to the serial port and configured it stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the...

10. UNIX for Advanced & Expert Users

UNIX Serial Port Redirector

Hi , I need to have an application where in I am able to create a virtual Serial port on a UNIX machine for a remote device which is accessible by a IP address and a port number (by terminal server). Both the machine and the remote device are on the same network. So after this application is...

LEARN ABOUT OSF1

dc

dc(7)							 Miscellaneous Information Manual						     dc(7)

NAME

       dc - serial line/mouse/keyboard

SYNOPSIS

       controller   dc0   at ibus0   slot 0   vector dcintr

DESCRIPTION

       The  dc	serial	line controller provides DECstation 2100, DECstation 3100, DECstation 5000, and DECstation 5100 computer systems with key-
       board, mouse, and serial communications interfaces. The serial communications interfaces on the DECstation 2100 and DECstation 3100 provide
       partial	modem  control.  The  serial communications interfaces on the DECstation 5000 provide full modem control.  The device special file
       /dev/tty01 on a DECstation 5100 provides full modem control, while the remaining ports provide no modem control at all.	All serial  commu-
       nications interfaces operate at baud rates from B50 to B9600, excluding B200.

       The  dc	ports  are  used as follows: Usage Graphics device keyboard at 4800 BPS Mouse or tablet at 4800 BPS Communications port 1 (w/modem
       control)/local terminal Communications port 2 (w/modem control)/local terminal

       On all systems except the DECstation 5100, serial port 2 is used for the system console port in server (that is,  non-graphics)	configura-
       tions.  On DECstation 5100s, the serial port labeled 3 on the back of the system is always the system console port.  The serial system con-
       sole port always operates at 9600 BPS, 8-bits, no parity; modem control is not supported.

RESTRICTIONS

       Data communications equipment attached to the console serial port in server configurations must be set to 9600 BPS, 8-bits, no parity.  The
       scc driver enforces this restriction.

FILES

       console terminal local terminal local terminal local terminal (DECstation 5100 only)

RELATED INFORMATION

       console(7), devio(7), tty(7), MAKEDEV(8) delim off

																	     dc(7)

UNIX for Dummies Questions & Answers