10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI.
I can get as far as plugging it in on my own.
Please help
Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
2. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
3. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
6. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
7. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
8. UNIX for Advanced & Expert Users
Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say:
pcipsy0: This is block
Can someone please help me. I trying to hook... (2 Replies)
Discussion started by: aojmoj
2 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks (2 Replies)
Discussion started by: nattie_h
2 Replies
10. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
AACRAID(4) BSD Kernel Interfaces Manual AACRAID(4)
NAME
aacraid -- Adaptec AACRAID Controller driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device aacraid
To compile in debugging code:
options AACRAID_DEBUG=N
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
aacraid_load="YES"
DESCRIPTION
The aacraid driver provides support for the Adaptec by PMC RAID controllers, including Series 6/7/8 and upcoming families.
The RAID containers are handled via the aacraidp0 bus. The physical buses are represented by the aacraidp? devices (beginning with
aacraidp1). These devices enable the SCSI pass-thru interface and allows devices connected to the card such as CD-ROMs to be available via
the CAM scsi(4) subsystem. Note that not all cards allow this interface to be enabled.
The /dev/aacraid? device nodes provide access to the management interface of the controller. One node exists per installed card. If the
kernel is compiled with the COMPAT_LINUX option, or the aacraid_linux.ko and linux.ko modules are loaded, the Linux-compatible ioctl(2)
interface for the management device will be enabled and will allow Linux-based management applications to control the card.
HARDWARE
Controllers supported by the aacraid driver include:
o Adaptec ASR-6405(T|E)
o Adaptec ASR-6445
o Adaptec ASR-6805(T|E|Q|TQ)
o Adaptec ASR-7085
o Adaptec ASR-7805(Q)
o Adaptec ASR-70165
o Adaptec ASR-71605(E|Q)
o Adaptec ASR-71685
o Adaptec ASR-72405
o Adaptec Series 8 cards
FILES
/dev/aacraid? aacraid management interface
DIAGNOSTICS
Compiling with AACRAID_DEBUG set to a number between 0 and 3 will enable increasingly verbose debug messages.
The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console, and are also
queued for retrieval by a management application.
SEE ALSO
kld(4), linux(4), scsi(4), kldload(8)
AUTHORS
Achim Leubner <achim@FreeBSD.org>
Ed Maste <emaste@FreeBSD.org>
Scott Long <scottl@FreeBSD.org>
BUGS
The controller is not actually paused on suspend/resume.
BSD
April 09, 2013 BSD