installing scsi card

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

Installing SCSI

I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI. I can get as far as plugging it in on my own. Please help Thanks

2. Solaris

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance.

3. UNIX for Dummies Questions & Answers

Problems with SCSI card and tape drive

Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system...

4. SCO

Installing SCSI Tape drive

Hello, I'm having some issues with installing SCSI tape drive on SCO 5.0.6 hardware config shows the following adapters %adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto %adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd %adapter - 3 - ...

5. SCO

configure Adaptec 29320ALP Ultra 320 SCSI Card in IBM X3400

I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120...

6. Solaris

Trouble Installing a SCSI Adapter

Okay. I admit I'm sort of a newbie in this regard. I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing. ...

7. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve...

8. UNIX for Advanced & Expert Users

Ultra 3 scsi card

Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say: pcipsy0: This is block Can someone please help me. I trying to hook...

9. UNIX for Dummies Questions & Answers

Installing a SCSI controller... problems

Hi, I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions? Thanks

10. Filesystems, Disks and Memory

help installing Sun 8mm unipack scsi tape drive

Hi all, please help I am stuck. I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the...

LEARN ABOUT NETBSD

sbp

SBP(4)							   BSD Kernel Interfaces Manual 						    SBP(4)

NAME

     sbp -- Serial Bus Protocol 2 (SBP-2) Mass Storage Devices driver

SYNOPSIS

     sbp* at ieee1394if? euihi ? euilo ?

DESCRIPTION

     The sbp driver provides support for SBP-2 devices that attach to the IEEE1394 port.  It should work with all SBP-2 devices which the scsi(4)
     layer supports, for example, HDDs, CDROM drives, and DVD drives.

     Some users familiar with umass(4) might wonder why the device is not detached at the scsi(4) layer when the device is unplugged.  It is
     detached only if the device has not been plugged again during several bus resets.	This is for preventing to detach an active file system
     even when the device cannot be probed correctly for some reason after a bus reset or when the device is temporary disconnected because the
     user changes the bus topology.  If you want to force to detach the device, run fwctl -r several times.

SEE ALSO

     ieee1394if(4), scsi(4), fwctl(8), scsictl(8), sysctl(8)

AUTHORS

     The sbp driver was written by Katsushi Kobayashi and Hidetoshi Shimokawa.

     This manual page was written by Katsushi Kobayashi.  It was added to NetBSD 4.0 by KIYOHARA Takashi.

BSD
								   June 18, 2005							       BSD

UNIX for Dummies Questions & Answers