10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI.
I can get as far as plugging it in on my own.
Please help
Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
2. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
3. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
6. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
7. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
8. UNIX for Advanced & Expert Users
Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say:
pcipsy0: This is block
Can someone please help me. I trying to hook... (2 Replies)
Discussion started by: aojmoj
2 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks (2 Replies)
Discussion started by: nattie_h
2 Replies
10. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)