9 More Discussions You Might Find Interesting
1. Red Hat
Hi Friends . my linux try to start very slowly after give it this error:
mount: wrong fs type, bad option, bad superblock on /dev/mapper/VolGroup-lv_root,
missing codepage or helper program, or other error
in some cases useful info is found in syslog - try
dmesg : tail or so
Kernel panic... (3 Replies)
Discussion started by: blackjuan
3 Replies
2. Shell Programming and Scripting
Objective: To recreate the partitioning setup of /dev/sda on /dev/sdc
How would I parse the below information and initialize variables
(an array?) that can be used to build sgdisk commands in a script, regardless of the number of partitions?
Something along the lines of:
sgdisk -n... (12 Replies)
Discussion started by: RogerBaran
12 Replies
3. SCO
I'm not sure exactly where to put this, so I'll just try here. I have an old SCO Openserver 5 box that has some important data on it. I had a hardware failure on the computer and can't boot from there. I obviously can't boot the drive from a different computer.
I tried to mount the HTFS filesystem... (6 Replies)
Discussion started by: Lazere
6 Replies
4. UNIX for Dummies Questions & Answers
Hi,
How to mount HTFS FS (from SCO UNIX) under linux?
Best regards.
where is link: htfs_fs-0.01alpha.tar.bz2 (2 Replies)
Discussion started by: EMREZ
2 Replies
5. SCO
I have a 17GB SCSI disk in an SCO 5.0.6 server and it's running out of space because of a growing database on the disk. Consequently I would like to upgrade the 17GB to a 74GB disk and extend the partition.
First off, is partition extension available under HTFS - I know this is an old... (1 Reply)
Discussion started by: carribey
1 Replies
6. Solaris
Hi, Anyone can help
My solaris 8 system has the following
/dev/null , /dev/tty and /dev/console
All permission are lrwxrwxrwx
Can this be change to a non-world write ??
any impact ?? (12 Replies)
Discussion started by: civic2005
12 Replies
7. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
8. UNIX for Advanced & Expert Users
If somebody solve this error please help me!
Thanks in advance! :confused: (7 Replies)
Discussion started by: FCollet
7 Replies
9. UNIX for Dummies Questions & Answers
# grep "Jul 3" syslog.messages | more
Jul 3 00:16:03 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:16:08 www3 CPU3: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:01 www3 CPU2: NOTICE: HTFS: No space on dev hd (1/42)
Jul 3 00:17:06 www3 syslogd: /usr/adm/debug: No space... (1 Reply)
Discussion started by: Cameron
1 Replies
vparutil(1M) vparutil(1M)
NAME
vparutil - get and set SCSI parameters for SCSI controllers from a virtual partition
SYNOPSIS
dev_path
dev_path
dev_path scsi_id] scsi_rate]
DESCRIPTION
The command gets and sets SCSI parameters for SCSI controllers within a running virtual partition. When setting the SCSI parameters using
the option, the virtual partition which owns the specified SCSI controller must be in the down state. If not, the command will fail with
the appropriate error code.
The SCSI parameters for a given SCSI controller must first be set (from the firmware BCH prompt or using the option) before the parameters
can be retrieved using the option.
The command is allowed on Itanium(R)-based platforms for compatibility. No action is taken for the command.
Options
recognizes the following command-line options:
Deletes an entry for the specified SCSI controller at
dev_path from the SCSI table.
Gets the SCSI parameters for the specified SCSI controller at
dev_path.
Sets the SCSI parameters for the specified SCSI controller at
dev_path.
Operands
recognizes the following command-line operands:
dev_path The device path of the SCSI controller.
id The SCSI ID for the specified controller (defaults to 7).
rate The SCSI rate for the specified controller. This parameter can have one of two values: for the corresponding fast wide and
ultra wide SCSI interfaces.
Note
For managing SCSI controllers, use corresponding SCSI utilities. For further information refer to
SECURITY RESTRICTIONS
This command is restricted to processes owned by superuser.
When virtual partition flexible administrative capability is enabled, only a Designated-Admin vPar can set SCSI parameters for SCSI con-
trollers.
EXAMPLES
Set the SCSI ID for controller at 0/0/2/0 to 3 with the fast wide rate:
RETURN VALUE
Successful.
Invalid SCSI controller specification.
Invalid SCSI ID.
Could not communicate with virtual partition monitor.
Virtual partition which owns SCSI controller is not in down state.
Internal firmware call failed.
Other error.
AUTHOR
was developed by the Hewlett-Packard Company.
SEE ALSO
vparadmin(1M), vparboot(1M), vparcreate(1M), vparconfig(1M), vpardump(1M), vparefiutil(1M), vparenv(1M), vparextract(1M), vparmodify(1M),
vparreloc(1M), vparremove(1M), vparreset(1M), vparstatus(1M), vparresources(5), vpartition(5), vpmon(5).
vparutil(1M)