8 More Discussions You Might Find Interesting
1. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
2. Solaris
Hi,
I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10).
I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies
3. Solaris
Hello all,
I have a problem with my x4270_m2 server. I have a GBE lan built into the back of my server and I have a QGE pci card in slot 2 to be used as a redundant.
My server is not picking up the QGE lan card in slot2. From investigation of the /etc/path_to_inst, which shows:
#grep e1000... (2 Replies)
Discussion started by: kerrygold
2 Replies
4. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
5. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
6. Solaris
Hi,
i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card .
Thank You,
Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies
7. Solaris
hello mates,
do you know a manufactor for rs232 serial pci cards for the sparc architecture? it seems that there is no original product from sun for that purpose. strange, isn't it?
problem is that i have a V250 with only one db9 rs232 serial port, and i need it for a modem connection, but i also... (1 Reply)
Discussion started by: pressy
1 Replies
8. SuSE
Hey all, ive got redhat 80 and trying to install a HCF win modem. Ive intsalled the drivers from linuxant.com using the rpm - i packagename.rpm command, but i still cant use the modem
any suggestions ? (3 Replies)
Discussion started by: kiwi_bloke
3 Replies
usb_create_pm_components(9F) Kernel Functions for Drivers usb_create_pm_components(9F)
NAME
usb_create_pm_components - Create power management components for USB devices
SYNOPSIS
#include <sys/usb/usba.h>
int usb_create_pm_components(dev_info_t *dip, uint_t *pwrstates);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI)
PARAMETERS
dip Pointer to the device's dev_info structure.
pwrstates Address into which a mask which lists power states capable by device is returned. This is a bitmask containing zero or more of
the following values:
USB_DEV_PWRMASK_D0 Corresponds to USB_DEV_OS_PWR_3 or full power.
USB_DEV_PWRMASK_D1 Corresponds to USB_DEV_OS_PWR_2.
USB_DEV_PWRMASK_D2 Corresponds to USB_DEV_OS_PWR_1.
USB_DEV_PWRMASK_D3 Corresponds to USB_DEV_OS_PWR_0 or no power.
DESCRIPTION
The usb_create_pm_components() function creates pm component properties that assume the standard USB D0-D3 powerlevels (USB_DEV_PWR_D0 -
USB_DEV_PWR_D3). See the device's relevant USB descriptor to determine the device's power management capabilities and account for bus-pow-
ered devices. The usb_create_pm_components() function also updates the pm-components property in the device's dev_info structure.
Note that these USB power levels are inverse of OS power levels. For example, USB_DEV_OS_PWR_0 and USB_DEV_PWR_D3 are equivalent levels
corresponding to powered-down.
RETURN VALUES
USB_SUCCESS Power management facilities in device are recognized by system.
USB_FAILURE An error occurred.
CONTEXT
May be called from user or kernel context.
EXAMPLES
uint_t *pwrstates;
/* Hook into device's power management. Enable remote wakeup. */
if (usb_create_pm_components(dip, pwrstates) == USB_SUCCESS) {
usb_handle_remote_wakeup(dip,USB_REMOTE_WAKEUP_ENABLE);
}
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |PCI-based systems |
+-----------------------------+-----------------------------+
|Interface stability |Committed |
+-----------------------------+-----------------------------+
|Availability |SUNWusb |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5), usb_clr_feature(9F), usb_register_hotplug_cbs(9F), usb_get_cfg(9F), usb_get_dev_data(9F), usb_handle_remote_wakeup(9F),
pm_idle_component(9F), pm_busy_component(9F), pm_raise_power(9F), pm_lower_power(9F), usb_cfg_descr(9S)
SunOS 5.11 5 Jan 2004 usb_create_pm_components(9F)