Visit Our UNIX and Linux User Community


Linux and my cable modem


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Linux and my cable modem
# 1  
Old 10-30-2001
Network Linux and my cable modem

I recently installed Caldera 2.4 (successfullySmilie ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now?
# 2  
Old 10-31-2001
if you have about $80 - $100 extra to spend, I would suggest a dsl/cable router. (linksys, smc barricade).

they are easy to setup and you can have your LAN up and running in no time regardless of the host's OS.

the problem I've seen a lot is that the software they give you with your cable modem is just for windoze.
# 3  
Old 10-31-2001
A DSL/Cable router is not going to help if the lan card is not working properly. You should get your network card functioning first. Make sure your card is supported (check the list of 3com cards here: http://www.linuxdocs.org/HOWTOs/Net-...54.html#AEN956). 'lsmod' may not list your ethernet card if the driver is compiled into the kernel. Check out the 'dmesg' command or look at the boot messages in /var/log/messages (or wherever Caldera puts them). You need to find out if the card was detected at boot-time.
# 4  
Old 11-01-2001
if you have any of the newer 3com cards, they are almost guaranteed to work on anything. all of my 3com cards have been successfully recognized by redhat, mandrake, suse, bsd, and solaris 7,8 x86.
# 5  
Old 11-02-2001
Java

You should still be able to manually install your 3Com card. Check your manual that came with your OS and look for the <b>modprobe</b> command for your particular adapter. This will probably be something like <b>modprobe 3c90x.o</b> assuming your 3Com card is a 90x model. You might want to try the tulip.o module first since it is generic and most NIC's will be able to use it without a problem. You can get a list of NIC modules in <b>/lib/modules/2.2.19/net</b> or something similar; the 2.2.19 is my kernel so yours might differ, but there is usually only one subdirectory in <b>/lib/modules</b>. If you don't have a manual you should propbably search Caldera's site for more info.

Once you get your NIC up Cable modem is much more straight forward to set up then DCL from my experience.
 

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies

2. Solaris

Need help configuring Cable Modem on Solaris x86

I have a dual boot system with XP being the primary for now and Solaris 10 being the Secondary. I have a cable modem and wish to configure the same to be used with Solaris so that I can browse the Internet and such. I have connected my x86 machine with a Netgear Router and that in turn is... (7 Replies)
Discussion started by: tubbyrana
7 Replies

3. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

4. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created... (1 Reply)
Discussion started by: fnoyan
1 Replies

5. UNIX for Dummies Questions & Answers

Installing Cable Modem on Irix Machine.

Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it... (1 Reply)
Discussion started by: Acidjack
1 Replies

6. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies

7. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies

8. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies

9. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies

10. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies

Featured Tech Videos