10 More Discussions You Might Find Interesting
1. AIX
Hi all, just after a bit of help..
I am attempting to read in the contents of a flat text file from one system to another using 'rsh', i have this setup over around 15 machines and it works for them all except one. On this one machine it just reads in a blank line for some reason. The machine... (21 Replies)
Discussion started by: forefather1977
21 Replies
2. Shell Programming and Scripting
Hello,
iḿ rather new to writing scripts in UNIX so i thought this would be a good start.
I need to write a script that can login to different hosts in a standalone network. That means there are no connection to Internet etc. I need to collect some data on the hosts, and they have different... (11 Replies)
Discussion started by: topy
11 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I have an old solaris 2.6 box and I need to copy all the data from the hard drive onto another machine. It does not have ssh installed so I am forced to use rsh. My plan was to execute the rcp command from the solaris box to a Centos 5 machine. I have installed rsh client and server on my... (1 Reply)
Discussion started by: mojoman
1 Replies
4. UNIX for Dummies Questions & Answers
Hello All,
I'm facing a weird problem with rsh.
There are 2 machines: host1.domain1.com and host2.domain2.com.
I have setup $HOME/.rhosts file in both the hosts.
When I login to host2.domain2.com and issue:
$ rsh host1
It works fine but
when I login to host1.domain1.com and... (2 Replies)
Discussion started by: sacguy08
2 Replies
5. UNIX for Dummies Questions & Answers
Dear forum,
First off, I'm using Solaris 5.6 UNIX. I'm trying to write a script which will connect to remote computers on a network (by specific IP's from a hosts file) and will run a separate script which is installed in each of the remote computers. My problem is that to run the script in the... (1 Reply)
Discussion started by: TheMightyUrrrrf
1 Replies
6. Shell Programming and Scripting
Dear,
I am trying to execute a script in the X machine by remote logging from machine Y. Note that in the X machine in host file the ip and the hostname of the Y is defined and in the .rhosts the hostname and the username of the Y is defined. By using the following:
rsh X -l username -n "sh... (0 Replies)
Discussion started by: tontal
0 Replies
7. Shell Programming and Scripting
I tried to execute by rsh a script, but I did not succeed.
You can execute only commnads (not scripts) by rsh or there are some other restrictions?!?
root@a1 #pwd
/
root@a1 #rsh a2 monitor
ksh: monitor: not found
On the other hand:
root@a1 #rsh a2
root@a2 #pwd
/
root@a2 #ls monitor... (9 Replies)
Discussion started by: heartwork
9 Replies
8. Shell Programming and Scripting
hey,
I'v a problem when I use rsh. When it logs in, it goes my home directory. I want it to go directly to my working directory. An idea I had was to redirect pwd to a file (pwd > somefile) and then once I'v rsh'd, cd to that path. I don't know how to read from the file to use as a parameter for... (2 Replies)
Discussion started by: Bacchus
2 Replies
9. Shell Programming and Scripting
Hi,
I am using rsh command in scripting. But I wan to run the script as a bg process.
When I run the script, it says stopped.
My doubt is ....if I use the rsh in scripting ......bg is possible or not ???
EX: test-rsh
rsh 172.16.73.38 df -k >DF.log
Result when I run this script ... (5 Replies)
Discussion started by: vastare
5 Replies
10. UNIX for Dummies Questions & Answers
Hi all
I have checked the archives and cannot find a solution.
I get a permission denied error, however all the suggestions donot help.
here is the scenario
root@OPSBOX#/>rsh OPSBOX ls -l
rshd: 0826-813 Permission is denied.
root@OPSBOX#/>pg .rhosts
OPSBOX root
OPSBOX ... (1 Reply)
Discussion started by: jhansrod
1 Replies
RSH(1) BSD General Commands Manual RSH(1)
NAME
rsh -- remote shell
SYNOPSIS
rsh [-46dn] [-l username] [-t timeout] host [command]
DESCRIPTION
The rsh utility executes command on host.
The rsh utility copies its standard input to the remote command, the standard output of the remote command to its standard output, and the
standard error of the remote command to its standard error. Interrupt, quit and terminate signals are propagated to the remote command; rsh
normally terminates when the remote command does. The options are as follows:
-4 Use IPv4 addresses only.
-6 Use IPv6 addresses only.
-d Turn on socket debugging (using setsockopt(2)) on the TCP sockets used for communication with the remote host.
-l username
Allow the remote username to be specified. By default, the remote username is the same as the local username. Authorization is deter-
mined as in rlogin(1).
-n Redirect input from the special device /dev/null (see the BUGS section of this manual page).
-t timeout
Allow a timeout to be specified (in seconds). If no data is sent or received in this time, rsh will exit.
If no command is specified, you will be logged in on the remote host using rlogin(1).
Shell metacharacters which are not quoted are interpreted on local machine, while quoted metacharacters are interpreted on the remote
machine. For example, the command
rsh otherhost cat remotefile >> localfile
appends the remote file remotefile to the local file localfile, while
rsh otherhost cat remotefile ">>" other_remotefile
appends remotefile to other_remotefile.
FILES
/etc/hosts
/etc/auth.conf
SEE ALSO
rlogin(1), setsockopt(2), rcmd(3), ruserok(3), auth.conf(5), hosts(5), hosts.equiv(5), rlogind(8), rshd(8)
HISTORY
The rsh command appeared in 4.2BSD.
BUGS
If you are using csh(1) and put a rsh in the background without redirecting its input away from the terminal, it will block even if no reads
are posted by the remote command. If no input is desired you should redirect the input of rsh to /dev/null using the -n option.
You cannot run an interactive command (like ee(1) or vi(1)) using rsh; use rlogin(1) instead.
Stop signals stop the local rsh process only; this is arguably wrong, but currently hard to fix for reasons too complicated to explain here.
BSD
October 16, 2002 BSD