Hello, So I was finally able to get mpd5 working as a vpn server, however I am not able to use encryption. I have a feeling it's this entry in the logs, can someone decipher what this means for me & tell me if it can be fixed? I know ng_mppc is related to mchap, but I'm not sure what I'm supposed to do to fix it.
Apr 4 10:28:36 freenas kernel: KLD ng_mppc.ko: depends on rc4 - not available
---------- Post updated 04-05-12 at 10:08 AM ---------- Previous update was 04-04-12 at 11:45 AM ----------
no love? ok here is the relevant part of my mpd.conf file, for a bump:
Code:
default:
load pptp_server
pptp_server:
# Define dynamic IP address pool.
set ippool add pool1 172.16.0.50 172.16.0.55
# Create clonable bundle template named B
create bundle template B
set iface enable proxy-arp
set iface idle 1800
set iface enable tcpmssfix
set ipcp yes vjcomp
# Specify IP address pool for dynamic assigment.
set ipcp ranges 172.16.0.1/32 ippool pool1
set ipcp dns 192.168.1.1
#set ipcp nbns 192.168.1.4
# The five lines below enable Microsoft Point-to-Point encryption
# (MPPE) using the ng_mppc(8) netgraph node type.
set bundle enable compression
set ccp yes mppc
set mppc yes e40
set mppc yes e128
set mppc yes stateless
# Create clonable link template named L
create link template L pptp
# Set bundle template to use
set link action bundle B
# Multilink adds some overhead, but gives full 1500 MTU.
set link enable multilink
set link yes acfcomp protocomp
set link no pap chap eap
set link enable chap
# We can use use RADIUS authentication/accounting by including
# another config section with label 'radius'.
# load radius
set link keep-alive 10 60
# We reducing link mtu to avoid GRE packet fragmentation.
set link mtu 1460
# Configure PPTP
set pptp self 192.168.1.124
# Allow to accept calls
set link enable incoming
Hi all,
I'm looking for secure file encryption tools that use MAC address as encryption key. FYI, I'm using Red Hat Enterprise Linux OS.
For example: when A wants to send file to B
A will encrypt the file with B's computer MAC/IP address as an encryption key
This file can only be decrypted... (2 Replies)
I try to setup a VPN Server (pptpd on Debian 5) to route an IP to my home PC when i login to the VPN - this works so far, i get the IP but then it is dead.
i cannot connect to anywhere, and only ping my IP - nothing else.
Any info on that?
I just want to have a static, external IP on the... (1 Reply)
Hi guys.
I am going to build a Linux VPN server(PPTP) for my friend but here is the problem:
He don't know Linux and command line to manage users, monitor server, etc
anyone knows a good GUI for this problem? I need some solution like nttacplus (2 Replies)
Hi all
I'd like to connect over pptp vpn.
I have my username, passwd and remote address. Then i start the connection and i see that over my ppp0 interface there's the same address in inet and P-t-P.
I think they should be different right?
Reading something i find out that i should change... (0 Replies)
My dilemma,
I need to send, deemed confidential, information via e-mail (SMTP). This information is sitting as a file on AIX. Typically I can send this data as a e-mail attachment via what we term a "mail filter" using telnet. I now would like to somehow encrypt the data and send it to a e-mail... (1 Reply)
Long story short, I have an issue with getting my VPN to connect to my w2k3 server box when I include the block all rule in my pf.conf:
block log all
Here's the output:
Apr 04 06:04:09.291697 rule 1/0(match): block in on hme0: call 3033 seq 0 gre-ppp-payload (gre encap)
Apr 04... (0 Replies)