Login or Register to Ask a Question and Join Our Community


UNIX for Dummies Questions & Answers

Network card and internet

 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Network card and internet
Prev   Next
# 3  
Old 11-08-2004
in short read the howto's and find out how to compile a kernel. enable the support for the card if they are supported.
and then load the module.

well if the module is alreayd in the kernel you can use the configure toos from redhat (as you should be able to find them in an howto) and enable it and then they drivers should work. in redhat it is "netconf ".
 
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

2. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

3. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies

4. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

5. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

7. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

8. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
Login or Register to Ask a Question

LEARN ABOUT DEBIAN

opensc-tool

OPENSC-TOOL(1)							   OpenSC tools 						    OPENSC-TOOL(1)

NAME

       opensc-tool - generic smart card utility

SYNOPSIS

       opensc-tool [OPTIONS]

DESCRIPTION

       The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
       sending arbitrary APDU commands to a card.

OPTIONS

       --info, -i
	   Print information about OpenSC, such as version and enabled components

       --atr, -a
	   Print the Answer To Reset (ATR) of the card, output is in hex byte format

       --name, -n
	   Print the name of the inserted card (driver)

       --serial
	   Print the card serial number (normally the ICCSN), output is in hex byte format

       --send-apdu apdu, -s apdu
	   Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF...

       --list-files, -f
	   Recursively lists all files stored on card

       --list-readers, -l
	   Lists all configured readers

       --list-drivers, -D
	   Lists all installed card drivers

       --reader num, -r num
	   Use the given reader number. The default is 0, the first reader in the system.

       --card-driver driver, -c driver
	   Use the given card driver. The default is auto-detected.

       --wait, -w
	   Wait for a card to be inserted

       --verbose, -v
	   Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.

SEE ALSO

       opensc-explorer(1)

opensc								    06/03/2012							    OPENSC-TOOL(1)