10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
3. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
6. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
7. Solaris
hi
Please give me the configuration steps for NTP server.
How do i sync other servers with this NTP server
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
8. Red Hat
Hi,
I'm trying to configure NTP client, however it failes to sync correctly.
Even after I manually set the time, once it connects with the NTP server, it pushes the time ahead by 4 hours.
We have set an AIX host as NTP server. It works fine for other AIX hosts, however fails on RHEL 5.4
... (4 Replies)
Discussion started by: max_min
4 Replies
9. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
10. IP Networking
How can I install ntp on AIX (4.3-5.1) ?
thnx (1 Reply)
Discussion started by: Gismo
1 Replies
MONGOCONNECTIONEXCEPTION(3) 1 MONGOCONNECTIONEXCEPTION(3)
The MongoConnectionException class
INTRODUCTION
Thrown when the driver fails to connect to the database.
There are a number of possible error messages to help you diagnose the connection problem. These are:
o No candidate servers found Thrown when the driver cannot establish a connection to MongoDB (fulfilling the ReadPreferences, if
specified).
o No server name given. This error occurs if you pass in "" as the server name, probably because of an typo with string interpola-
tion, e.g., "$servr" instead of "$server".
o
failed to get host [hostname] or port [portnum] from [server]. This indicated that the server string was malformed. "[hostname]"
and "[portnum]" will be as much as the driver could dicipher of it.
o Operation in progress Connecting to the database timed out.
o Transport endpoint is not connected Generally means that the connection string isn't correct, the driver couldn't even find the
database server.
o couldn't determine master No server in a replica set connection was identified as the primary.
o couldn't get host info for [server] This indicated that DNS could not resolve the server address you gave. This could easily be
caused by a typo, for example, "server" instead of "$server".
o Invalid Argument This can be caused by attempting to connect to a machine that is up but that the database isn't actually running
on. Make sure that you've started the database server before connecting.
o Permission denied This means that the socket could not be opened due to permissions issues. On Red Hat variants, this can be
caused by a default setting that does not allow Apache to create network connections. You can override this setting by running:
$ /usr/sbin/setsebool -P httpd_can_network_connect 1
If the error message is not listed above, it is probably an error from the C socket, and you can search the web for its usual cause.
CLASS SYNOPSIS
MongoConnectionException
MongoConnectionExceptionextends
MongoException
PHP Documentation Group MONGOCONNECTIONEXCEPTION(3)
ntp configuration