10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
3. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
6. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
7. Solaris
hi
Please give me the configuration steps for NTP server.
How do i sync other servers with this NTP server
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
8. Red Hat
Hi,
I'm trying to configure NTP client, however it failes to sync correctly.
Even after I manually set the time, once it connects with the NTP server, it pushes the time ahead by 4 hours.
We have set an AIX host as NTP server. It works fine for other AIX hosts, however fails on RHEL 5.4
... (4 Replies)
Discussion started by: max_min
4 Replies
9. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
10. IP Networking
How can I install ntp on AIX (4.3-5.1) ?
thnx (1 Reply)
Discussion started by: Gismo
1 Replies
DPKG-RECONFIGURE(8) Debconf DPKG-RECONFIGURE(8)
NAME
dpkg-reconfigure - reconfigure an already installed package
SYNOPSIS
dpkg-reconfigure [options] packages
DESCRIPTION
dpkg-reconfigure reconfigures packages after they have already been installed. Pass it the names of a package or packages to reconfigure.
It will ask configuration questions, much like when the package was first installed.
If you just want to see the current configuration of a package, see debconf-show(1) instead.
OPTIONS
-ftype, --frontend=type
Select the frontend to use. The default frontend can be permanently changed by:
dpkg-reconfigure debconf
Note that if you normally have debconf set to use the noninteractive frontend, dpkg-reconfigure will use the dialog frontend instead,
so you actually get to reconfigure the package.
-pvalue, --priority=value
Specify the minimum priority of question that will be displayed. dpkg-reconfigure normally shows low priority questions no matter what
your default priority is. See debconf(7) for a list.
--default-priority
Use whatever the default priority of question is, instead of forcing the priority to low.
-u, --unseen-only
By default, all questions are shown, even if they have already been answered. If this parameter is set though, only questions that have
not yet been seen will be asked.
--force
Force dpkg-reconfigure to reconfigure a package even if the package is in an inconsistent or broken state. Use with caution.
--no-reload
Prevent dpkg-reconfigure from reloading templates. Use with caution; this will prevent dpkg-reconfigure from repairing broken templates
databases. However, it may be useful in constrained environments where rewriting the templates database is expensive.
-h, --help
Display usage help.
SEE ALSO
debconf(7)
AUTHOR
Joey Hess <joeyh@debian.org>
2018-02-28 DPKG-RECONFIGURE(8)