10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
3. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
6. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
7. Solaris
hi
Please give me the configuration steps for NTP server.
How do i sync other servers with this NTP server
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
8. Red Hat
Hi,
I'm trying to configure NTP client, however it failes to sync correctly.
Even after I manually set the time, once it connects with the NTP server, it pushes the time ahead by 4 hours.
We have set an AIX host as NTP server. It works fine for other AIX hosts, however fails on RHEL 5.4
... (4 Replies)
Discussion started by: max_min
4 Replies
9. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
10. IP Networking
How can I install ntp on AIX (4.3-5.1) ?
thnx (1 Reply)
Discussion started by: Gismo
1 Replies
ARITHMETIC(6) BSD Games Manual ARITHMETIC(6)
NAME
arithmetic -- quiz on simple arithmetic
SYNOPSIS
arithmetic [-o +-x/] [-r range]
DESCRIPTION
arithmetic asks you to solve problems in simple arithmetic. Each question must be answered correctly before going on to the next. After
every 20 problems, it prints the score so far and the time taken. You can quit at any time by typing the interrupt or end-of-file character.
The options are as follows:
-o By default, arithmetic asks questions on addition of numbers from 0 to 10, and corresponding subtraction. By supplying one or more
of the characters +-x/, you can ask for problems in addition, subtraction, multiplication, and division, respectively. If you give
one of these characters more than once, that kind of problem will be asked correspondingly more often.
-r If a range is supplied, arithmetic selects the numbers in its problems in the following way. For addition and multiplication, the
numbers to be added or multiplied are between 0 and range, inclusive. For subtraction and division, both the required result and the
number to divide by or subtract will be between 0 and range. (Of course, arithmetic will not ask you to divide by 0.) The default
range is 10.
When you get a problem wrong, arithmetic will remember the numbers involved, and will tend to select those numbers more often than others, in
problems of the same sort. Eventually it will forgive and forget.
arithmetic cannot be persuaded to tell you the right answer. You must work it out for yourself.
DIAGNOSTICS
``What?'' if you get a question wrong. ``Right!'' if you get it right. ``Please type a number.'' if arithmetic doesn't understand what you
typed.
SEE ALSO
bc(1), dc(1)
BSD
May 31, 1993 BSD