10 More Discussions You Might Find Interesting
1. IP Networking
How would one approach the problem of determining the NAT tables of a router without knowing the userid and password. The only password holder died.
I know the internal ip address of the router is 192.168.2.1, and also ports 80 or 8080 and 3389 are open. (5 Replies)
Discussion started by: jgt
5 Replies
2. IP Networking
Hi,
I am trying to figure out a way to partition the departmental IP network address block to create a staff and a student subnet. Each of these will be identified by its own network address and netmask. It is university policy that you must be economical with the IP addresses. That is, the... (0 Replies)
Discussion started by: bawse.c
0 Replies
3. Shell Programming and Scripting
Hello,
I am running a post script in autoyast where I am trying to set the broadcast and network address.
I have the ip address and netmask already (reading from a file)..
I saw the post from fpmurphy but it is using ksh which isn't an option in autoyast.
Thanks in advance! (3 Replies)
Discussion started by: bloodclot
3 Replies
4. IP Networking
Thanks in advance!
Ben (1 Reply)
Discussion started by: bigben1220
1 Replies
5. IP Networking
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
Discussion started by: wilsonSurya
3 Replies
6. Shell Programming and Scripting
Hi
Suppose
You have two computers. One named kenny which has an IP address of 192.168.0.7. kenny lives
on a subnet with a subnet mask of 255.255.255.240. The second computer is called zathras, which
has an IP address of 192.168.0.17, zathras lives on a network with the same subnet mask.
i)... (4 Replies)
Discussion started by: scofiled83
4 Replies
7. IP Networking
HI folks,
I am developing a software which one of the module is to interchange the ip address of another active network interface's when making a socket connection.
I would like to know whether there is any function call that would enable me to retrieve the ip address that is obtained by a... (2 Replies)
Discussion started by: citiz3n
2 Replies
8. AIX
Hi, I try to understand how to configure my ethernet network in a hacmp cluster.
I have 2 nodes, 3 lan port on each node, and 1 service ip to cluster.
I don't have any serial o iscsi heartbeat.
Do you suggest me a possibile ip address configuration? I've many error whene I verify it from hacmp... (3 Replies)
Discussion started by: hacmp
3 Replies
9. HP-UX
Hie everyone,
I am currently facing a problem whereby I can not connect to an external network from a package ip address on a HP-UX cluster. Below is the illustration:
Primary Server IP Address : n.n.n.202
Secondary Server IP Address : n.n.n.212
Package IP Address : n.n.n.211
... (1 Reply)
Discussion started by: cchilenga
1 Replies
10. UNIX for Dummies Questions & Answers
say I have a IP address which is 10.0.0.12, and subnet mask is 255.255.255.240, what is the network address and what is the broadcast address which host lives on?
And could you explain how to get the answer?
thanx in advance! (7 Replies)
Discussion started by: pnxi
7 Replies
I2C-STUB-FROM-DUMP(8) System Manager's Manual I2C-STUB-FROM-DUMP(8)
NAME
i2c-stub-from-dump - feed i2c-stub with dump files
SYNOPSIS
i2c-stub-from-dump address[,address,...] dump-file [dump-file ...]
DESCRIPTION
i2c-stub-from-dump is a small helper script for the i2c-stub kernel driver. It lets you setup one or more fake I2C chips on the i2c-stub
bus based on dumps of the chips you want to emulate.
i2c-stub-from-dump requires i2cdetect and i2cset to be installed and reachable through the user's PATH. The former is used to find out the
i2c-stub bus number, while the latter is used to write to the fake I2C chips.
EXAMPLE
You have an I2C chip on system A. You would like to do some development on its driver on system B. Here are the few steps you have to fol-
low.
On system A, use i2cdump to capture a dump from the chip. Assuming that the chip in question lives at address 0x4c on I2C bus 0, you would
run:
i2cdump -y 0 0x4c b > chip.dump
Adjust the bus number and chip address for your case. i2cdetect can help you find out their values. If the device uses word (16-bit) regis-
ter access instead of the traditional byte (8-bit) access, use mode w instead of b.
Copy the dump file to system B.
On system B, run:
i2c-stub-from-dump 0x4c chip.dump
This will load the required i2c-dev and i2c-stub kernel drivers if needed, then write all the register values to the emulated I2C chip at
address 0x4c. Again, adjust the address as needed.
LIMITATIONS
There are some limitations to the kind of devices that can be handled:
o Device must not have banks (as most Winbond devices do).
SEE ALSO
i2cdump(8), i2cdetect(8), i2cset(8)
AUTHOR
Jean Delvare
March 2010 I2C-STUB-FROM-DUMP(8)