10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Discussion started by: fretagi
4 Replies
2. Red Hat
I'm using redhat 5.1 installed on VMware work station9. Can you guys help me to
configure redhat clusters. (1 Reply)
Discussion started by: karthik9358
1 Replies
3. Emergency UNIX and Linux Support
Hi All,
I installed Red-hat linux(64bit-x86) os on vmware 8,configure IP address and services but it is unable to come in to network.it is production server.
please provide solution to me , it is very urgent... (3 Replies)
Discussion started by: Rajesh_Apple
3 Replies
4. Linux
Hi All,
I installed Red-hat linux(64bit-x86) os on vmware 8,configure IP address and services but it is unable to come in to network.it is production server.
please provide solution to me , it is very urgent... (2 Replies)
Discussion started by: Rajesh_Apple
2 Replies
5. Solaris
Hello
I want to ask that how to mount and run fsck in SVM disk.In my scenario if i have to disks c0t0d0 and c0t1d0 these two disks are in Mirroring (raid1) if i want to run fsck on the disks than below are the right steps?
ok boot cdrom -s
mount /dev/dsk/c0t0d0s0 /a
cd /a
fsck... (3 Replies)
Discussion started by: jhonnybravo
3 Replies
6. UNIX for Advanced & Expert Users
Hi All,
I want to know what is the Interlace value in SVM and what is the need of this ?
regards,
prashant (1 Reply)
Discussion started by: prashant2507198
1 Replies
7. UNIX for Advanced & Expert Users
How to list out multiple Disk sets in SVM
# metaset -s <disksetname> --- This will list out only one diskset
but I need a list of disk sets configured for the node.
Is there any command,please let me know ...
Thanks in advance. (1 Reply)
Discussion started by: pramath
1 Replies
8. UNIX for Dummies Questions & Answers
i have taken two separate disk
A and B
created 4 slices in each
A b
s4 s4
s5 s5
s6 s6
s7 s7
took slices s4 of A and slice s6 0f B ---created a meta device d0
took slices s4 of B and slice s6 0f A---created a meta device d1
created main mirror d2 using d0... (1 Reply)
Discussion started by: vivek_ng
1 Replies
9. Solaris
I am trying to set up a new server. It has 8 HD's in it. I am using 2 for the system disk. IE set one up mirror to the other. I am using the other 6 as data disks. For those I want to concat 3 together, mirror to the other 3 (also concated together of course) and then make various soft... (7 Replies)
Discussion started by: NewSolarisAdmin
7 Replies
10. Solaris
gurus,
i have configured the LUN's in solaris 10.after labeled the disk,i have added the disk into one of the soft partition using metattach d0 c5t1000d10s6.actully before that i should confiure the powermt and than i should have add metattch d0 emcpowerc2.i forget to do that and increased... (0 Replies)
Discussion started by: rjay.com
0 Replies
PMDAVMWARE(1) Performance Co-Pilot PMDAVMWARE(1)
NAME
pmdavmware - VMware performance metrics domain agent (PMDA)
DESCRIPTION
pmdavmware is a Performance Metrics Domain Agent (PMDA) which exports metric values from a (possibly remote) VMware virtualisation host.
This implementation uses the VMare Perl API (refer to the online docs at http://www.vmware.com/support/developer/viperltoolkit). VIPerl is
a prerequisite for this PMDA, it needs to be installed and configured before attempting to use this agent. It is highly recommended that
you test your VIPerl installation using the demo programs that are shipped with VIPerl, before attempting to use this PMDA.
INSTALLATION
In order to access performance data using the VIPerl API, it is necessary to be able to login to the metrics source. Hence, a valid VMware
server name, user name and pass word are needed by the PMDA. These can be passed in on the command line (via the pmcd.conf file) or via a
vmware.conf file in the PMDA directory.
# cd $PCP_PMDAS_DIR/vmware
# [ edit vmware.conf ]
This file should contain three lines, such as:
$server = 'vm.server.net';
$username = 'XXXX';
$password = 'YYYY';
Once this is setup, you can access the names and values for the vmware performance metrics by doing the following as root:
# cd $PCP_PMDAS_DIR/vmware
# ./Install
If you want to undo the installation, do the following as root:
# cd $PCP_PMDAS_DIR/vmware
# ./Remove
pmdavmware is launched by pmcd(1) and should never be executed directly. The Install and Remove scripts notify pmcd(1) when the agent is
installed or removed.
FILES
$PCP_PMDAS_DIR/vmware/vmware.conf
configuration file for the pmdavmware agent
$PCP_PMDAS_DIR/vmware/Install
installation script for the pmdavmware agent
$PCP_PMDAS_DIR/vmware/Remove
undo installation script for the pmdavmware agent
$PCP_LOG_DIR/pmcd/vmware.log
default log file for error messages from pmdavmware
SEE ALSO
pmcd(1).
3.8.10 Performance Co-Pilot PMDAVMWARE(1)